Sanyo 8.53E+13 How to connect wiring to the terminal For Indoor Unit, For stranded wiring

Page 12

05-423 KHS0971-1271 12/13/05 1:23 PM Page 12

WARNING Loose wiring may cause the terminal to overheat or result

in unit malfunction. A fire hazard may also exist. There- fore, be sure all wiring is tightly connected.

When connecting each power wire to the corresponding terminal, follow the instructions “How to connect wiring to the terminal” and fasten the wire securely tight with the fixing screw of the terminal plate.

How to connect wiring to the terminal

a) For Indoor Unit

9/32"

STRIP (7 mm) (ACTUAL

SIZESIZE)

(1)Cut the wire end with a cutting pliers, then strip the insulation to expose the wire about 9/32" (7 mm). See the label (Fig. 28) near the terminal plate.

(2)Using a screwdriver, loosen the terminal screw on the terminal plate.

(3)Insert the wire and tighten the terminal screw com- pletely using a screwdriver.

b) For Outdoor Unit

■For solid core wiring (or F-cable)

(1)Cut the wire end with a cutting pliers, then strip the insulation to expose the solid wire about 15/16" (25 mm). (Fig. 29)

(2)Using a screwdriver, remove the terminal screw(s) on the terminal plate.

(3)Using the pliers, bend the solid wire to form a loop suitable for the terminal screw.

(4)Shape the loop wire properly, place it on the termi- nal plate and fix it securely with the removed termi- nal screw using a screwdriver.

■For stranded wiring

(1)

Cut the wire end with a cutting pliers, then strip the

 

insulation to expose the stranded wiring about 3/8"

 

(10 mm) and tightly twist the wire ends. (Figs. 30

 

and 31)

(2)

Using a screwdriver, remove the terminal screw(s)

 

on the terminal plate.

(3)

Using a ring connector fastener or pliers, securely

 

clamp each stripped wire end with a ring connector.

 

(Fig. 30)

(4)

Place the ring connector wire, and replace and

 

tighten the removed terminal screw using a screw-

 

driver. (Fig. 32)

Special washer

Wire

Fig. 28

Strip 15/16" (25mm)

Solid wire

Insulation

 

 

Fig. 29

Strip 3/8" (10 mm)

Stranded wire

 

Fig. 30

Twist wire ends

Fig. 31

Screw

Ring connector

Terminal plate

Loop

Ring connector

Screw and special washer

Ring connector

Wire

Fig. 32

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Installation Instructions ContentsFor safe installation and trouble-free operation, you must …In a Ceiling or Wall…In a Room …In Moist or Uneven LocationsTools Required for Installation not supplied Accessories Supplied with Unit TableGeneral Optional Copper Tubing KitInstallation Site Selection Additional Materials Required for InstallationIndoor Unit Front ViewOutdoor Unit Solid base must not coverHole of the bottom plate How to Install the Indoor Unit Trical wiring or conduits areRemove the Rear Panel from the Unit Make a HoleInstall the Rear Panel on the Wall If Wooden WallIf Block, Brick, Concrete or Similar Type Wall Hole DiaRemove the Grille to Install the Indoor Unit How to replace the grilleWiring Instructions General precautions on wiring Shape the Indoor Side TubingRecommended Wire Length and Diameter Wiring Instructions for Inter-unit Connections How to connect wiring to the terminal For Indoor Unit For Outdoor Unit For solid core wiring or F-cableFor stranded wiring Mounting Right-side tubingSwitching drain hose and drain cap Left-side tubingDrain hose Drain capDo not supply power to Tubing and wiring to the outTo unmount indoor unit Unit or operate it until allHow to Install the Outdoor Unit Wiring Instructions for the Outdoor UnitFlaring Procedure with a Flare Tool To 0.5 mm Adjust so that the amount of tubeRefrigerant Tubing Use of the Flaring MethodConnecting Tubing between Indoor and Outdoor Units Finishing the InstallationInsulation of Refrigerant Tubing Tube Dia Tightening TorqueAir Purging Be sure to completely insert Hex wrench beforeAttempting to turn the valve How to Test Run the Air Conditioner Operation lamp Timer lamp Quiet lamp ION lampBasic Functions of the Service Valves Pump DownRemote Control Unit Installation Position To take out the remote control unit, pull it forwardMounting on a Wall Address Switch Address Setting of the Remote Control Unit

8.53E+13 specifications

Sanyo 8.53E+13 is a remarkable product that stands out in the world of consumer electronics, showcasing a blend of advanced technology and innovative features. This impressive device is primarily a part of Sanyo's extensive lineup of high-capacity batteries, known for their reliability and longevity.

One of the standout features of the Sanyo 8.53E+13 is its superior energy density. With a capacity of approximately 8.53E+13 mAh, this battery is designed to provide extended usage times for electronic devices, making it an ideal choice for both personal and professional applications. Users can expect longer performance periods without the need for frequent recharging, which is a significant advantage in today's fast-paced lifestyle.

The Sanyo 8.53E+13 employs advanced lithium-ion technology that enhances its performance and safety. This technology not only allows for rapid charging but also minimizes the chances of overheating and battery degradation over time. The lithium-ion cells are engineered to deliver consistent power output, ensuring that devices powered by this battery deliver peak performance throughout their operating times.

Another key characteristic of the Sanyo 8.53E+13 is its robust design. Built to withstand varying environmental conditions, this battery is resistant to extreme temperatures and impact, making it suitable for outdoor activities and rugged usage. Its durability ensures a longer lifespan, which is an essential consideration for users who rely on their devices in demanding situations.

The Sanyo 8.53E+13 also prioritizes environmental sustainability. Sanyo has adopted eco-friendly practices in the manufacturing process of their batteries, focusing on reducing waste and promoting recycling. This commitment to sustainability is increasingly important to consumers who are looking for products that align with their environmental values.

In terms of compatibility, the Sanyo 8.53E+13 is versatile and can be used in various applications, from portable electronics to electric vehicles. Its adaptability makes it a sought-after choice among manufacturers and consumers alike, who require a dependable power source.

Overall, the Sanyo 8.53E+13 exemplifies the innovative spirit of Sanyo, combining cutting-edge technologies with practical features that meet the needs of modern users. Its energy efficiency, safety, durability, and commitment to the environment position it as a leading option in the battery market, making it an essential component for powering the devices of the future.
Top Page Image Contents