Remove the Grille to Install the Indoor Unit

05-423 KHS0971-1271 12/13/05 1:23 PM Page 8

3-4. Remove the Grille to Install the Indoor Unit

Basically, these models can be installed and wired without removing the grille. If access to any internal part is need- ed, follow the steps as given below.

Air intake grille

Grille

CAUTION

Be sure to wear work gloves

during installation to avoid being

cut by the sharp aluminum finsFig. 16a of the heat exchanger.

How to remove the grille

(1)Grasp both ends of the air intake grille, and remove it by opening towards the front and pulling towards you. (Fig. 16a)

(2)Remove the 2 screws. (Fig. 16b)

(3)Remove the screw on the right side cover plate and open the cover. (Fig. 17a)

(4)Take out the thermistor from the grille. (Fig. 17b)

(5)Pull the lower part of the grille toward you to remove. (Fig. 18a)

(6)Use a standard screwdriver to push on the tabs to remove the grille.

How to replace the grille

(1)Reinstall the grille into the lower part while aligning its tabs on the upper part. (Fig. 18b) Insert the tabs in the slots and push the lower part of the grille back into position.

(2)Make sure that the grille and frame are firmly fitted together by engaging the tabs.

(3)Attach the thermistor on the grille. (Fig. 17a)

(4)Close the cover and replace the screw. (Fig. 17a)

(5)Affix the grille with the 2 previously removed screws. (Fig. 16b)

(6)Install the air intake grille.

(a)Allow the edge of the air intake grille to slide into the top of the indoor unit, and then insert it all the way inside. (Fig. 19a)

(b)Press the bottom right and left corners of the air intake grille to attach it to the indoor unit. (Fig. 19b)

NOTE

Attach so that the round pins at the top right and left cor- ners of the air intake grille are inserted into the grooves at the top right and left of the indoor unit.

Fig. 19b

Screw cover

Fig. 16b

Cover

Thermistor

	Thermistor
Fig. 17a	Fig. 17b
Tab	*
	*
*	Grille
*

Frame

Tab

Fig. 18a

Fig. 18b

Groove

8	Fig. 19a

8.53E+13 specifications

Sanyo 8.53E+13 is a remarkable product that stands out in the world of consumer electronics, showcasing a blend of advanced technology and innovative features. This impressive device is primarily a part of Sanyo's extensive lineup of high-capacity batteries, known for their reliability and longevity.

One of the standout features of the Sanyo 8.53E+13 is its superior energy density. With a capacity of approximately 8.53E+13 mAh, this battery is designed to provide extended usage times for electronic devices, making it an ideal choice for both personal and professional applications. Users can expect longer performance periods without the need for frequent recharging, which is a significant advantage in today's fast-paced lifestyle.

The Sanyo 8.53E+13 employs advanced lithium-ion technology that enhances its performance and safety. This technology not only allows for rapid charging but also minimizes the chances of overheating and battery degradation over time. The lithium-ion cells are engineered to deliver consistent power output, ensuring that devices powered by this battery deliver peak performance throughout their operating times.

Another key characteristic of the Sanyo 8.53E+13 is its robust design. Built to withstand varying environmental conditions, this battery is resistant to extreme temperatures and impact, making it suitable for outdoor activities and rugged usage. Its durability ensures a longer lifespan, which is an essential consideration for users who rely on their devices in demanding situations.

The Sanyo 8.53E+13 also prioritizes environmental sustainability. Sanyo has adopted eco-friendly practices in the manufacturing process of their batteries, focusing on reducing waste and promoting recycling. This commitment to sustainability is increasingly important to consumers who are looking for products that align with their environmental values.

In terms of compatibility, the Sanyo 8.53E+13 is versatile and can be used in various applications, from portable electronics to electric vehicles. Its adaptability makes it a sought-after choice among manufacturers and consumers alike, who require a dependable power source.

Overall, the Sanyo 8.53E+13 exemplifies the innovative spirit of Sanyo, combining cutting-edge technologies with practical features that meet the needs of modern users. Its energy efficiency, safety, durability, and commitment to the environment position it as a leading option in the battery market, making it an essential component for powering the devices of the future.