Sanyo 8.53E+13 Be sure to completely insert, Hex wrench before, Attempting to turn the valve

Page 20

05-423 KHS0971-1271 12/13/05 1:23 PM Page 20

(5)With the vacuum pump still running, close the “Lo” knob of the manifold valve. Then stop the vacuum pump.

(6)With the accessory hex wrench, turn the valve stem on the narrow tube service valve counter-clockwise by 90 degrees (1/4 turn) for 10 seconds, and then turn the stem clockwise to close it again. (Fig. 58)

CAUTION

Be sure to completely insert

the hex wrench before

 

 

 

attempting to turn the valve.

(7)Leak test all joints at the tubing (both indoor and out- doors) with soapy water. Bubbles indicate a leak. Tight- en the joint more when leaks, then check if there is no leak. Be sure to wipe off the soap with a clean cloth.

(8)With the hex wrench, turn the wide tube service valve stem counter-clockwise to fully open the valve.

(9)Turn the narrow tube service valve stem counter- clockwise to fully open the valve.

(10)Loosen the vacuum hose connected to the wide tube service port slightly to release the pressure. Then, remove the hose.

CAUTION This may cause the refriger- ant gas to leak. In order to avoid this, take off the hose quickly.

(11)Fasten the valve cap on the wide tube service port securely with an adjustable wrench or box wrench. Next, mount the valve cap on the service valve and tighten it to 170 lbs·in (200 kgf·cm) with a torque wrench. This process is very important to prevent gas from leaking from the system.

(12)Test run the air conditioner. (See next page.)

(13)While the air conditioner is running, apply liquid soap to check for any gas leaks around the service valves or caps.

(14)If there is no leakage, stop the air conditioner.

(15)Wipe off the soap on the tubing.

This completes air purging with a vacuum pump and the air conditioner is ready for actual operation.

90° (1/4 turn)

Narrow tube

Hex wrench

Wide tube

Valve cap

Vacuum hose to manifold valve

Fig. 58

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Installation Instructions ContentsFor safe installation and trouble-free operation, you must …In a Ceiling or Wall…In a Room …In Moist or Uneven LocationsTools Required for Installation not supplied Accessories Supplied with Unit TableGeneral Optional Copper Tubing KitInstallation Site Selection Additional Materials Required for InstallationIndoor Unit Front ViewHole of the bottom plate Outdoor UnitSolid base must not cover How to Install the Indoor Unit Trical wiring or conduits areRemove the Rear Panel from the Unit Make a HoleInstall the Rear Panel on the Wall If Wooden WallIf Block, Brick, Concrete or Similar Type Wall Hole DiaRemove the Grille to Install the Indoor Unit How to replace the grilleWiring Instructions General precautions on wiring Shape the Indoor Side TubingRecommended Wire Length and Diameter Wiring Instructions for Inter-unit Connections For stranded wiring How to connect wiring to the terminal For Indoor UnitFor Outdoor Unit For solid core wiring or F-cable Mounting Right-side tubingSwitching drain hose and drain cap Left-side tubingDrain hose Drain capDo not supply power to Tubing and wiring to the outTo unmount indoor unit Unit or operate it until allHow to Install the Outdoor Unit Wiring Instructions for the Outdoor UnitFlaring Procedure with a Flare Tool To 0.5 mm Adjust so that the amount of tubeRefrigerant Tubing Use of the Flaring MethodConnecting Tubing between Indoor and Outdoor Units Finishing the InstallationInsulation of Refrigerant Tubing Tube Dia Tightening TorqueAir Purging Attempting to turn the valve Be sure to completely insertHex wrench before How to Test Run the Air Conditioner Operation lamp Timer lamp Quiet lamp ION lampBasic Functions of the Service Valves Pump DownMounting on a Wall Remote Control Unit Installation PositionTo take out the remote control unit, pull it forward Address Switch Address Setting of the Remote Control Unit

8.53E+13 specifications

Sanyo 8.53E+13 is a remarkable product that stands out in the world of consumer electronics, showcasing a blend of advanced technology and innovative features. This impressive device is primarily a part of Sanyo's extensive lineup of high-capacity batteries, known for their reliability and longevity.

One of the standout features of the Sanyo 8.53E+13 is its superior energy density. With a capacity of approximately 8.53E+13 mAh, this battery is designed to provide extended usage times for electronic devices, making it an ideal choice for both personal and professional applications. Users can expect longer performance periods without the need for frequent recharging, which is a significant advantage in today's fast-paced lifestyle.

The Sanyo 8.53E+13 employs advanced lithium-ion technology that enhances its performance and safety. This technology not only allows for rapid charging but also minimizes the chances of overheating and battery degradation over time. The lithium-ion cells are engineered to deliver consistent power output, ensuring that devices powered by this battery deliver peak performance throughout their operating times.

Another key characteristic of the Sanyo 8.53E+13 is its robust design. Built to withstand varying environmental conditions, this battery is resistant to extreme temperatures and impact, making it suitable for outdoor activities and rugged usage. Its durability ensures a longer lifespan, which is an essential consideration for users who rely on their devices in demanding situations.

The Sanyo 8.53E+13 also prioritizes environmental sustainability. Sanyo has adopted eco-friendly practices in the manufacturing process of their batteries, focusing on reducing waste and promoting recycling. This commitment to sustainability is increasingly important to consumers who are looking for products that align with their environmental values.

In terms of compatibility, the Sanyo 8.53E+13 is versatile and can be used in various applications, from portable electronics to electric vehicles. Its adaptability makes it a sought-after choice among manufacturers and consumers alike, who require a dependable power source.

Overall, the Sanyo 8.53E+13 exemplifies the innovative spirit of Sanyo, combining cutting-edge technologies with practical features that meet the needs of modern users. Its energy efficiency, safety, durability, and commitment to the environment position it as a leading option in the battery market, making it an essential component for powering the devices of the future.
Top Page Image Contents