Bosch Power Tools DDS182-02, DDS182BL, DDS182BN manual Operating Tips, Brake, Built in Work Light

Page 11

BM 2610032211 09-13_BM 2610032211 09-13.qxp 9/26/13 8:55 AM Page 11

BRAKE

When the trigger switch is released it activates the brake to stop the chuck quickly. This is especially useful in the repetitive driving and removal of screws.

BUILT IN WORK LIGHT

Your tool is also equipped with a light that turns on automatically when the switch is activated, for better visibility when drilling/driving (Fig. 1).

DRILL/HAMMER DRILL SELECTOR RING

(Model HDS182 only)

The selector ring allows the tool to be set for various drilling/hammer drilling applications. Rotate the selector dial right or left depending on the below applications (Fig. 9).

Drill only action: For drilling in woods, metals, plastics or other non concrete materials.

Drill with hammer action: For drilling in concrete, asphalt, tile or other similar hard materials. The hammer drill position overrides the clutch for hammer drilling.

FIG. 9

MODE

SELECTOR

RING

INSERTING AND RELEASING BATTERy PACK

Set Forward/Reversing lever to the center (off position). Slide charged battery pack into the housing until the battery pack locks into position (Fig. 10).

Your tool is equipped with a secondary locking latch to prevent the battery pack from completely falling out of the handle, should it become loose due to vibration.

To remove the battery pack, press the battery pack release button and slide the battery pack forward (Fig. 11).

Press the battery pack release button again and slide the battery pack completely out of tool housing (Fig. 11).

FIG. 10

BATTERY PACK

FIG. 11

 

RELEASE BUTTON

 

BATTERY PACK

 

 

1

2

Operating Tips

You will extend the life of your bits and do neater work if you always put the bit in contact with the work before pulling the trigger. During the operation, hold the tool firmly and exert light, steady pressure. Too much pressure at low speed will stall the tool. Too little pressure will keep the bit from

cutting and cause excess friction by sliding over the surface. This can be damaging to both tool and bit.

DRILLING WITH VARIABLE SPEED

The trigger controlled variable speed feature will eliminate the need for center punches in

-11-

Image 11
Contents See Voir Ver la página Leer antes de usarCall Toll Free for Personal safety General Power Tool Safety WarningsWork area safety Electrical safetyService Safety Rules for Cordless Drill/DriversBattery tool use and care Wear ear protectors when impact drilling Safety Rules for Cordless Hammer DrillsAdditional Safety Warnings Symbol Name Designation/Explanation SymbolsSymbols Cordless Drill Drivers Cordless Hammer Drills Functional Description and SpecificationsRubberized Grip Belt Clip Battery Pack 4X BIT TIP Holder AssemblyInserting Bits Chuck Sleeve Drill BIT BIT Holder Screwdriver BIT Belt ClipFORWARD/REVERSING Lever & Trigger Lock Variable Speed Controlled Trigger SwitchAdjustable Clutch Operating InstructionsDRILL/HAMMER Drill Selector Ring Operating TipsBrake Built in Work LightDrilling Wood Driving with Variable SpeedFastening with Screws Drill BitsCleaning MaintenanceAccessories Sécurité électrique Sécurité du lieu de travailEntretien Consignes de sécurité pour perceuses/tournevis sans cordonUtilisation et entretien des outils Électroportatifs Utilisation et entretien des outils à pilesPage Le plomb provenant des peintures à base de plomb Avertissements supplémentaires concernant la sécuritéSymbole Nom Désignation/Explication SymbolesSymboles suite Description fonctionnelle et spécifications Attache À LA Ceinture PORTE-MÈCHE AssemblageInsertion DES Forets Changement DE Vitesses Consignes de fonctionnementLevier DE Marche AVANT/ARRIÈRE ET Verrouillage DE Gâchette Consignes de fonctionnement Fixation ’AIDE DE VIS Enfoncement À Vitesse VariableFixation À L’AIDE DE VIS Perçage DU BoisNettoyage EntretienAccessoires Uso y cuidado de las herramientas Mecánicas Seguridad del área de trabajoSeguridad eléctrica Servicio de ajustes y reparaciones Uso y cuidado de las herramientas Alimentadas por bateríasNormas de seguridad para taladros de percusión sin cordón Advertencias de seguridad adicionales Símbolo Nombre Designación/explicación SímbolosSímbolos continuación Paquetes de batería/Cargadores de baterías Descripción funcional y especificacionesNúmero de modelo Capacidades máximasClip DE Cinturón EnsamblajeColocacion DE LAS Brocas Manguito DEL Mandril Brocas TaladroInstrucciones de funcionamiento Consejos de funcionamiento Taladrado DE Metal Sujecion CON TornillosBrocas Para Taladro Taladrado DE MaderaLimpieza MantenimientoServicio Accesorios BM 2610032211 09-13BM 2610032211 09-13.qxp 9/26/13 856 AM Remarques Notas 2610031211