Grizzly G0756 owner manual Control Panel

Page 6

Control Panel

A

B

C

F

D

G

 

H

I

E

Figure 1. Control panel

A.Spindle Speed Levers: Used to get spindle speed at available RPMs.

B.Coolant Pump Switch: Turns pump on, sending coolant to nozzle

C.High/Low Spindle Speed Range Switch: Selects high/low range for spindle speed.

D.Spindle Rotation Switch: Controls direction.

E.Spindle Stop Button: Stops all work.

F.Working Lamp Switch: Turns work light on or off.

G.EMERGENCY STOP Button: Immediately cuts power to motor and control panel when pressed. Remains depressed until button is reset by twisting clockwise.

H.Drilling/Tapping Switch: Selects between drilling and tapping modes.

I.Spindle Start Button: Starts machine when Master Power Switch has already been turned to the ON position and the high/low spindle speed range switch is turned to 1 or 2.

-4-

Model G0756 (Mfg. Since 2/13)

Image 6
Contents Model G0756 Industrial Drill Press Page Table of Contents Introduction Machine Description Manual AccuracyContact Info Identification Control Panel Machine Data Sheet Main Specifications Operation Info Safety Safety Instructions for MachineryPage Safety for Drill Presses Full-Load Current Rating Power SupplyAvailability Circuit Requirements forMinimum Gauge Size 14 AWG Grounding InstructionsExtension Cords 50 ftUnpackingInventory SetupNeeded for Setup Inventory see Figure QtyCleanup Before cleaning, gather the followingBasic steps for removing rust preventative Site Considerations Lifting & Placing Anchoring to FloorAnchoring to Concrete Floors Arbor/Chuck Assembly Initial LubricationTo connect the drill chuck with the arbor Power Connection To connect the power cord to the machineMaster power switch Model G0756 Mfg. Since 2/13 Test RunEmergency Test Coolant System To test the coolant systemTo perform the spindle break-in procedure Spindle Break-InTooling Installation Removal OperationsOperations Overview Installing Tapered Tooling Removing Tooling with Automatic DriftRemoving Tooling Manually Raising/Lowering Table Depth StopTable Positioning Rotating TableSelecting Spindle To determine the needed RPMDrilling Mode Automatic Power Downfeed Tapping Mode Coolant System To use tapping modeTo operate the coolant system ACcESSORIES G1075-52-PC. Clamping KitG3658-Titanium Drill Bits H7616 H7617H7819-Drill & Tap HSS 24 pc. Set H8262-1⁄2 x MT#4 Keyless Chuck with Integral ShankMaintenance Cleaning ProtectingSchedule To change oil in headstock LubricationHeadstock Lubrication Oil Flow Sight GlassChanging Coolant Ball OilersSymptom Possible Cause Possible Solution ServiceTroubleshooting Motor & ElectricalDrill Press Operations Replacing Lamp Bulb Torque LimiterTo replace the bulb in the work lamp Wiring Wiring Safety InstructionsWiring Overview Component Location IndexHot 220 VAC Power Connection WiringElectric Clutch Wiring PlugMotor & Pump Wiring Spindle motor wiringViewed from behind Control Panel & Limit Switches Electrical Panel Wiring QM5 QM3 QM2 QM1Electrical Wiring Panel Photo Electrical wiring panel Model G0756 Mfg. Since 2/13Parts Table Support & Coolant BreakdownTable Support & Coolant Parts List DescriptionGearbox Breakdown Gearbox Breakdown Gearbox Parts List Spindle Feed Breakdown Spindle Feed Parts List Headstock Breakdown Headstock Breakdown Headstock Parts List Electrical Parts Breakdown Electrical Parts List DescriptionLabels & Cosmetics 506 502 503 501 508 509 507 510 504 511 505 512 513Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty & Returns