Grizzly G0756 owner manual Drilling Mode

Page 28

Drilling Mode

This drill press is designed for vertical drilling and tapping operations. For repeated drilling at the same depth, there is a power downfeed mecha- nism. For tapping convenience, there is an auto- matic clutch used for reversing the direction of the spindle while in tapping mode by pressing one of the buttons at the ends of each course downfeed handle.

Overloading tools or using excessive spin- dle speeds may cause parts or broken tools to hit operator, resulting in serious impact injuries.

-26-

To drill a workpiece:

1. Refer to Controls on Page 4 to understand the functions of each control.

Speed Control Levers

Drilling/Taping Switch

Figure 23. Controls for drilling.

2. Clamp the workpiece to the table, and adjust the depth stop for the needed depth of cut.

Note: Drilling with the quill fully extended can cause tool chatter. For maximum spindle rigidity, keep the spindle retracted into the headstock as far as possible.

3. Put on safety glasses, a face shield, and close the chip guard.

4. Select the "drilling" mode option with the toggle switch.

5. Refer to Selecting Spindle RPM on Page 25, and choose the closest available spindle RPM.

6. turn the Master Power Switch ON.

7. Press the spindle start button and begin the drilling operation.

Model G0756 (Mfg. Since 2/13)

Image 28
Contents Model G0756 Industrial Drill Press Page Table of Contents Machine Description Manual Accuracy IntroductionContact Info Identification Control Panel Machine Data Sheet Main Specifications Operation Info Safety Safety Instructions for MachineryPage Safety for Drill Presses Power Supply AvailabilityFull-Load Current Rating Circuit Requirements forGrounding Instructions Extension CordsMinimum Gauge Size 14 AWG 50 ftSetup Needed for SetupUnpackingInventory Inventory see Figure QtyBefore cleaning, gather the following CleanupBasic steps for removing rust preventative Site Considerations Anchoring to Floor Lifting & PlacingAnchoring to Concrete Floors Initial Lubrication Arbor/Chuck AssemblyTo connect the drill chuck with the arbor Power Connection To connect the power cord to the machineMaster power switch Model G0756 Mfg. Since 2/13 Test RunEmergency Test Coolant System To test the coolant systemTo perform the spindle break-in procedure Spindle Break-InOperations Tooling Installation RemovalOperations Overview Removing Tooling with Automatic Drift Installing Tapered ToolingRemoving Tooling Manually Depth Stop Table PositioningRaising/Lowering Table Rotating TableSelecting Spindle To determine the needed RPMDrilling Mode Automatic Power Downfeed To use tapping mode Tapping Mode Coolant SystemTo operate the coolant system ACcESSORIES G1075-52-PC. Clamping KitG3658-Titanium Drill Bits H7616 H7617H7819-Drill & Tap HSS 24 pc. Set H8262-1⁄2 x MT#4 Keyless Chuck with Integral ShankCleaning Protecting MaintenanceSchedule Lubrication Headstock LubricationTo change oil in headstock Oil Flow Sight GlassChanging Coolant Ball OilersService TroubleshootingSymptom Possible Cause Possible Solution Motor & ElectricalDrill Press Operations Torque Limiter Replacing Lamp BulbTo replace the bulb in the work lamp Wiring Wiring Safety InstructionsWiring Overview Component Location IndexPower Connection Wiring Electric Clutch WiringHot 220 VAC PlugMotor & Pump Wiring Spindle motor wiringViewed from behind Control Panel & Limit Switches Electrical Panel Wiring QM5 QM3 QM2 QM1Electrical Wiring Panel Photo Electrical wiring panel Model G0756 Mfg. Since 2/13Parts Table Support & Coolant BreakdownTable Support & Coolant Parts List DescriptionGearbox Breakdown Gearbox Breakdown Gearbox Parts List Spindle Feed Breakdown Spindle Feed Parts List Headstock Breakdown Headstock Breakdown Headstock Parts List Electrical Parts Breakdown Electrical Parts List DescriptionLabels & Cosmetics 506 502 503 501 508 509 507 510 504 511 505 512 513Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty & Returns