Grizzly G0756 owner manual Depth Stop, Table Positioning, Raising/Lowering Table, Rotating Table

Page 26

Depth Stop

This drill press includes a depth stop for drilling multiple holes at the same depth.

To set the depth stop:

1.DISCONNECT MACHINE FROM POWER!

2.Adjust the table height so the workpiece is close to the work tool.

3.Mark the side of your workpiece at the intend- ed cutting depth (see Figure 19).

Workpiece

Drill Bit

Scrap Wood

Workpiece

Depth

Mark

Table

Figure 19. Depth stop mark on workpiece.

4. Secure the workpiece to the table with a clamp or vise.

5.Place the workpiece on the table, and lower the spindle until the tip of the bit is even with the mark.

6.Loosen the depth stop handle, move the drill bit to the required drilling depth, and tighten it (see Figure 20).

Depth Stop Handle

Figure 20. Setting depth stop handle.

-24-

7. Press the spindle start button.

8.Drill a hole into scrap stock before drilling into any workpiece to ensure the depth has been set correctly. If necessary, repeat Steps 2–5.

Table Positioning

The table for this drill press moves vertically and rotates 360 degrees to accommodate larger workpieces.

Raising/Lowering Table

1. Remove any objects from the table surface.

2. Loosen the release handles shown in Figure

21).

3. Adjust the table height by rotating the height adjustment handle (see Figure 21).

Height

Adjustment

Handle

Lock Handles

Figure 21. Column Release and Height

Adjustment Handles.

Rotating Table

1. Remove all objects from the table surface.

2. Slightly loosen the lock handles (see Figure

21).

3. Push the table to the desired location, and guide the rack on the side of the column.

4. Re-tighten the lock handles.

Model G0756 (Mfg. Since 2/13)

Image 26
Contents Model G0756 Industrial Drill Press Page Table of Contents Contact Info IntroductionMachine Description Manual Accuracy Identification Control Panel Machine Data Sheet Main Specifications Operation Info Safety Safety Instructions for MachineryPage Safety for Drill Presses Full-Load Current Rating Power SupplyAvailability Circuit Requirements forMinimum Gauge Size 14 AWG Grounding InstructionsExtension Cords 50 ftUnpackingInventory SetupNeeded for Setup Inventory see Figure QtyBasic steps for removing rust preventative CleanupBefore cleaning, gather the following Site Considerations Anchoring to Concrete Floors Lifting & PlacingAnchoring to Floor To connect the drill chuck with the arbor Arbor/Chuck AssemblyInitial Lubrication Power Connection To connect the power cord to the machineMaster power switch Model G0756 Mfg. Since 2/13 Test RunEmergency Test Coolant System To test the coolant systemTo perform the spindle break-in procedure Spindle Break-InOperations Overview Tooling Installation RemovalOperations Removing Tooling Manually Installing Tapered ToolingRemoving Tooling with Automatic Drift Raising/Lowering Table Depth StopTable Positioning Rotating TableSelecting Spindle To determine the needed RPMDrilling Mode Automatic Power Downfeed To operate the coolant system Tapping Mode Coolant SystemTo use tapping mode ACcESSORIES G1075-52-PC. Clamping KitG3658-Titanium Drill Bits H7616 H7617H7819-Drill & Tap HSS 24 pc. Set H8262-1⁄2 x MT#4 Keyless Chuck with Integral ShankSchedule MaintenanceCleaning Protecting To change oil in headstock LubricationHeadstock Lubrication Oil Flow Sight GlassChanging Coolant Ball OilersSymptom Possible Cause Possible Solution ServiceTroubleshooting Motor & ElectricalDrill Press Operations To replace the bulb in the work lamp Replacing Lamp BulbTorque Limiter Wiring Wiring Safety InstructionsWiring Overview Component Location IndexHot 220 VAC Power Connection WiringElectric Clutch Wiring PlugMotor & Pump Wiring Spindle motor wiringViewed from behind Control Panel & Limit Switches Electrical Panel Wiring QM5 QM3 QM2 QM1Electrical Wiring Panel Photo Electrical wiring panel Model G0756 Mfg. Since 2/13Parts Table Support & Coolant BreakdownTable Support & Coolant Parts List DescriptionGearbox Breakdown Gearbox Breakdown Gearbox Parts List Spindle Feed Breakdown Spindle Feed Parts List Headstock Breakdown Headstock Breakdown Headstock Parts List Electrical Parts Breakdown Electrical Parts List DescriptionLabels & Cosmetics 506 502 503 501 508 509 507 510 504 511 505 512 513Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty & Returns