Grizzly G0756 owner manual Test Coolant System, To test the coolant system

Page 22

Test Coolant System

This drill press comes with a pump-driven cycling coolant system. Prior to testing the coolant sys- tem, add two gallons of coolant to the coolant res- ervoir. Refer to Changing Coolant on Page 28.

To test the coolant system:

1. Wear safety goggles and other protective clothing.

2. Aim the coolant nozzle into the trough to reduce splash (see Figure 13).

 

 

Coolant Drain

Table trough

 

 

 

 

 

 

 

Figure 13. Table trough and coolant drain.

-20-

3. turn the Coolant Pump Switch to the ON position.

4. Adjust the ball valve in the coolant nozzle assembly for the proper coolant flow (see Figure 14).

Ball valve

Figure 14. Ball valve of nozzle assembly.

5. Close the ball valve and turn the pump switch to the OFF position.

Running the pump without adequate cool- ant can significantly damage the pump, which will not be covered under warranty.

Model G0756 (Mfg. Since 2/13)

Image 22
Contents Model G0756 Industrial Drill Press Page Table of Contents Machine Description Manual Accuracy IntroductionContact Info Identification Control Panel Machine Data Sheet Main Specifications Operation Info Safety Safety Instructions for MachineryPage Safety for Drill Presses Full-Load Current Rating Power SupplyAvailability Circuit Requirements forMinimum Gauge Size 14 AWG Grounding InstructionsExtension Cords 50 ftUnpackingInventory SetupNeeded for Setup Inventory see Figure QtyBefore cleaning, gather the following CleanupBasic steps for removing rust preventative Site Considerations Anchoring to Floor Lifting & PlacingAnchoring to Concrete Floors Initial Lubrication Arbor/Chuck AssemblyTo connect the drill chuck with the arbor Power Connection To connect the power cord to the machineMaster power switch Model G0756 Mfg. Since 2/13 Test RunEmergency Test Coolant System To test the coolant systemTo perform the spindle break-in procedure Spindle Break-InOperations Tooling Installation RemovalOperations Overview Removing Tooling with Automatic Drift Installing Tapered ToolingRemoving Tooling Manually Raising/Lowering Table Depth StopTable Positioning Rotating TableSelecting Spindle To determine the needed RPMDrilling Mode Automatic Power Downfeed To use tapping mode Tapping Mode Coolant SystemTo operate the coolant system ACcESSORIES G1075-52-PC. Clamping KitG3658-Titanium Drill Bits H7616 H7617H7819-Drill & Tap HSS 24 pc. Set H8262-1⁄2 x MT#4 Keyless Chuck with Integral ShankCleaning Protecting MaintenanceSchedule To change oil in headstock LubricationHeadstock Lubrication Oil Flow Sight GlassChanging Coolant Ball OilersSymptom Possible Cause Possible Solution ServiceTroubleshooting Motor & ElectricalDrill Press Operations Torque Limiter Replacing Lamp BulbTo replace the bulb in the work lamp Wiring Wiring Safety InstructionsWiring Overview Component Location IndexHot 220 VAC Power Connection WiringElectric Clutch Wiring PlugMotor & Pump Wiring Spindle motor wiringViewed from behind Control Panel & Limit Switches Electrical Panel Wiring QM5 QM3 QM2 QM1Electrical Wiring Panel Photo Electrical wiring panel Model G0756 Mfg. Since 2/13Parts Table Support & Coolant BreakdownTable Support & Coolant Parts List DescriptionGearbox Breakdown Gearbox Breakdown Gearbox Parts List Spindle Feed Breakdown Spindle Feed Parts List Headstock Breakdown Headstock Breakdown Headstock Parts List Electrical Parts Breakdown Electrical Parts List DescriptionLabels & Cosmetics 506 502 503 501 508 509 507 510 504 511 505 512 513Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty & Returns