Grizzly G0756 owner manual Safety for Drill Presses

Page 11

Safety for Drill Presses

EYE/FACE/HAND PROTECTION. A face shield used with safety glasses is recommended. Always keep hands and fingers away from the drill bit. Never hold a workpiece by hand while drilling! Do Not wear gloves when operating the drill.

SECURING BIT. Properly tighten and securely lock the drill bit in the chuck.

CORRECT BIT. Use only round, hex, or triangular shank drill bits.

ADJUSTING KEYS AND WRENChES. Remove all adjusting keys and wrenches before turning the machine ON.

DRILLING SHEET METAL. Never drill sheet metal unless it is securely clamped to the table.

SURFACE/WORKPIECE PREP. Never turn the drill press ON before clearing the table of all objects (tools, scrap wood, etc.) Do Not drill material that does not have a flat surface, unless a suitable support is used.

DAMAGED TOOLS. Never use drill bits in poor condition. Dull or damaged drill bits are hard to control and may cause serious injury.

DRILL OPERATION. Never start the drill press with the drill bit pressed against the workpiece. Feed the drill bit evenly into the workpiece. Back the bit out frequently to clear deep holes.

CLEARING CHIPS. Turn the machine OFF and clear chips and scrap pieces with a brush. Disconnect power, remove drill bit, and clean table before leaving the machine.

OPERATING SPEED. Always operate your drill press at speeds that are appropriate for the drill bit size and the material that you are drilling.

MOUNTING WORKPIECES. Use clamps or vises to secure workpiece before drilling. Position work so you avoid drilling into the table.

TABLE LOCK. Make sure the table lock is tight- ened before starting the drill press.

MAINTENANCE/SPEED CHANGES. Never change speeds or do maintenance with the machine connected to power.

EXPERIENCING DIFFICULTIES. If at any time you are experiencing difficulties performing the intended operation, stop using the machine! Contact our Technical Support at (570) 546-9663.

Like all machines there is danger associated with this machine. Accidents are frequently caused by lack of familiarity or failure to pay attention. Use this machine with respect and caution to lessen the possibility of operator injury. If normal safety precautions are overlooked or ignored, serious personal injury may occur.

No list of safety guidelines can be complete. Every shop environment is different. Always consider safety first, as it applies to your individual working conditions. Use this and other machinery with caution and respect. Failure to do so could result in serious per- sonal injury, damage to equipment, or poor work results.

Model G0756 (Mfg. Since 2/13)

-9-

Image 11
Contents Model G0756 Industrial Drill Press Page Table of Contents Contact Info IntroductionMachine Description Manual Accuracy Identification Control Panel Machine Data Sheet Main Specifications Operation Info Safety Instructions for Machinery SafetyPage Safety for Drill Presses Circuit Requirements for Power SupplyAvailability Full-Load Current Rating50 ft Grounding InstructionsExtension Cords Minimum Gauge Size 14 AWGInventory see Figure Qty SetupNeeded for Setup UnpackingInventoryBasic steps for removing rust preventative CleanupBefore cleaning, gather the following Site Considerations Anchoring to Concrete Floors Lifting & PlacingAnchoring to Floor To connect the drill chuck with the arbor Arbor/Chuck AssemblyInitial Lubrication To connect the power cord to the machine Power ConnectionTest Run Master power switch Model G0756 Mfg. Since 2/13Emergency To test the coolant system Test Coolant SystemSpindle Break-In To perform the spindle break-in procedureOperations Overview Tooling Installation RemovalOperations Removing Tooling Manually Installing Tapered ToolingRemoving Tooling with Automatic Drift Rotating Table Depth StopTable Positioning Raising/Lowering TableTo determine the needed RPM Selecting SpindleDrilling Mode Automatic Power Downfeed To operate the coolant system Tapping Mode Coolant SystemTo use tapping mode G1075-52-PC. Clamping Kit ACcESSORIESH7616 H7617 G3658-Titanium Drill BitsH8262-1⁄2 x MT#4 Keyless Chuck with Integral Shank H7819-Drill & Tap HSS 24 pc. SetSchedule MaintenanceCleaning Protecting Oil Flow Sight Glass LubricationHeadstock Lubrication To change oil in headstockBall Oilers Changing CoolantMotor & Electrical ServiceTroubleshooting Symptom Possible Cause Possible SolutionDrill Press Operations To replace the bulb in the work lamp Replacing Lamp BulbTorque Limiter Wiring Safety Instructions WiringComponent Location Index Wiring OverviewPlug Power Connection WiringElectric Clutch Wiring Hot 220 VACSpindle motor wiring Motor & Pump WiringViewed from behind Control Panel & Limit Switches QM5 QM3 QM2 QM1 Electrical Panel WiringElectrical wiring panel Model G0756 Mfg. Since 2/13 Electrical Wiring Panel PhotoTable Support & Coolant Breakdown PartsDescription Table Support & Coolant Parts ListGearbox Breakdown Gearbox Breakdown Gearbox Parts List Spindle Feed Breakdown Spindle Feed Parts List Headstock Breakdown Headstock Breakdown Headstock Parts List Electrical Parts Breakdown Description Electrical Parts List506 502 503 501 508 509 507 510 504 511 505 512 513 Labels & CosmeticsComments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty & Returns