HP Z Virtual manual SAS and Sata device numbers Hot-plug drive LED definitions, Led

Page 19

SAS and SATA device numbers

Hot-plug drive LED definitions

Item

LED

Status

Definition

 

 

 

 

1

Locate

Solid blue

The drive is being identified by a host application.

 

 

 

 

 

 

Flashing blue

The drive carrier firmware is being updated or

 

 

 

requires an update.

 

 

 

 

2

Activity ring

Rotating green

Drive activity

 

 

 

 

 

 

Off

No drive activity

 

 

 

 

3

Do not remove

Solid white

Do not remove the drive. Removing the drive causes

 

 

 

one or more of the logical drives to fail.

 

 

 

 

 

 

Off

Removing the drive does not cause a logical drive to

 

 

 

fail.

 

 

 

 

4

Drive status

Solid green

The drive is a member of one or more logical drives.

 

 

 

 

 

 

Flashing green

The drive is rebuilding or performing a RAID

 

 

 

migration, strip size migration, capacity expansion, or

 

 

 

logical drive extension, or is erasing.

 

 

 

 

 

 

Flashing amber/green

The drive is a member of one or more logical drives

 

 

 

and predicts the drive will fail.

 

 

 

 

 

 

Flashing amber

The drive is not configured and predicts the drive will

 

 

 

fail.

 

 

 

 

 

 

Solid amber

The drive has failed.

 

 

 

 

 

 

Off

The drive is not configured by a RAID controller.

 

 

 

 

SAS and SATA device numbers 13

Image 19
Contents HP DL380z Gen8 Virtual Workstation Part number First Edition April Table of contents Setup Active Health System Integrated Management Log 101 Abstract Front panel components Component identificationDescription Status Front panel LEDs and buttonsSystems Insight Display LEDs Access the Systems Insight DisplayRJ-45 LEDs for status Rear panel LEDs and buttons Systems Insight Display LED combinationsPage Rear panel components Non-hot-plug PCI riser board slot definitions Rear panel LEDs and buttonsFL/FH ItemDescription System board componentsDefault Function System maintenance switchDimm slot locations NMI functionalityLED SAS and Sata device numbers Hot-plug drive LED definitionsPCI riser cage LED Amber Green Interpretation Fbwc module LEDs P420Hot-plug fans Page Power down the server Power up the serverOperations Extend the server from the rack Install the access panel Remove the access panelOpening the cable management arm Access the product rear panelRemove the hot-plug fan cage Power down the server onRemove the hot-plug fan Remove the access panel onRemove the full-length expansion board Remove the PCI riser cage Install the access panel on Install the PCI riser cageSecure the full-length expansion board retainer Remove the air baffle Page Optional installation services SetupSpace and airflow requirements Optimum environmentPower requirements Temperature requirementsElectrical grounding requirements Connecting a DC power cable to a DC power source Installing hardware options Identifying the contents of the server shipping cartonRack warnings Installing the server into the rack Page Citrix XenServer Installing the operating systemVMware vSphere Registering the server Powering on and selecting boot optionsIntroduction Hardware options installationMemory options Memory subsystem architecture HP SmartMemoryDimm identification Single-, dual-, and quad-rank DIMMs1Maximum capacity Memory configurationsAdvanced ECC memory configuration Advanced ECC population guidelines General Dimm slot population guidelinesLockstep Memory population guidelines Installing a DimmHot-plug hard drive options Power up the server onInstalling a hot-plug SAS or Sata hard drive Removing a hot-plug SAS or Sata hard drive Controller optionsInstalling the flash-backed write cache module Installing the flash-backed write cache capacitor pack Page Remove the Velcro liner Hardware options installation Power up the server on Optical drive option 48V DC power supply option Page Page Page Page FlexibleLOM option FlexibleLOM option Removing the expansion slot blanks Expansion board optionsPage Installing a half-length expansion board Installing a full-length expansion board Secondary PCI riser cage option Page Install the secondary PCI riser cage HP Trusted Platform Module option 2U rack bezel optionInstalling the Trusted Platform Module board HP Trusted Platform Module option Enabling the Trusted Platform Module Retaining the recovery key/passwordSAS hard drive cabling CablingOptical drive cabling Fbwc cabling Chipset Sata cable option Remove the air baffle on Cabling PCIe power cable option Server mode Software and configuration utilitiesHP product QuickSpecs HP iLO HP iLO Management EngineIntegrated Management Log Intelligent ProvisioningErase Utility HP Insight Remote Support softwareScripting Toolkit HP Smart Update Manager HP Service Pack for ProLiantUsing Rbsu HP ROM-Based Setup UtilityBoot options Auto-configuration processConfiguring AMP modes Array Configuration Utility Utilities and featuresRe-entering the server serial number and product ID Option ROM Configuration for Arrays HP Smart Storage AdministratorROMPaq utility Automatic Server RecoveryDrivers Keeping the system currentUSB support Redundant ROM supportSoftware and firmware Version control Change control and proactive notification Troubleshooting resources TroubleshootingLocate the battery System board components on Battery replacementPage Power supply specifications SpecificationsEnvironmental specifications Mechanical specificationsSpecification Value Input requirements HP 1200 W CS HE Power Supply 94% efficiencyBefore you contact HP Support and other resourcesHP contact information Customer Self Repair 101 Acronyms and abbreviationsAcronyms and abbreviations Documentation feedback ASR IndexIML