HP Z Virtual Temperature requirements, Power requirements, Electrical grounding requirements

Page 38

Temperature requirements

To ensure continued safe and reliable equipment operation, install or position the system in a well- ventilated, climate-controlled environment.

The maximum recommended ambient operating temperature (TMRA) for most server products is 35° C (95° F). The temperature in the room where the rack is located must not exceed 35° C (95° F).

CAUTION: To reduce the risk of damage to the equipment when installing third-party options:

●Do not permit optional equipment to impede airflow around the server or to increase the internal rack temperature beyond the maximum allowable limits.

●Do not exceed the manufacturer’s TMRA.

Power requirements

Installation of this equipment must comply with local and regional electrical regulations governing the installation of information technology equipment by licensed electricians. This equipment is designed to operate in installations covered by NFPA 70, 1999 Edition (National Electric Code) and NFPA-75, 1992 (code for Protection of Electronic Computer/Data Processing Equipment). For electrical power ratings on options, refer to the product rating label or the user documentation supplied with that option.

WARNING! To reduce the risk of personal injury, fire, or damage to the equipment, do not overload the AC supply branch circuit that provides power to the rack. Consult the electrical authority having jurisdiction over wiring and installation requirements of your facility.

CAUTION: Protect the server from power fluctuations and temporary interruptions with a regulating uninterruptible power supply. This device protects the hardware from damage caused by power surges and voltage spikes and keeps the system in operation during a power failure.

When installing more than one server, you may need to use additional power distribution devices to safely provide power to all devices. Observe the following guidelines:

●Balance the server power load between available AC supply branch circuits.

●Do not allow the overall system AC current load to exceed 80% of the branch circuit AC current rating.

●Do not use common power outlet strips for this equipment.

●Provide a separate electrical circuit for the server.

Electrical grounding requirements

The server must be grounded properly for proper operation and safety. In the United States, you must install the equipment in accordance with NFPA 70, 1999 Edition (National Electric Code), Article 250, as well as any local and regional building codes. In Canada, you must install the equipment in accordance with Canadian Standards Association, CSA C22.1, Canadian Electrical Code. In all other countries, you must install the equipment in accordance with any regional or national electrical wiring codes, such as the International Electrotechnical Commission (IEC) Code 364, parts 1 through 7. Furthermore, you must be sure that all power distribution devices used in the installation, such as branch wiring and receptacles, are listed or certified grounding-type devices.

Because of the high ground-leakage currents associated with multiple servers connected to the same power source, HP recommends the use of a PDU that is either permanently wired to the building’s branch circuit or includes a nondetachable cord that is wired to an industrial-style plug. NEMA

32 Chapter 4 Setup

Page 37 Page 39
Image 38
Page 37 Page 39
Contents HP DL380z Gen8 Virtual Workstation Part number First Edition April Table of contents Setup Active Health System Integrated Management Log 101 Abstract Component identification Front panel componentsFront panel LEDs and buttons Description StatusAccess the Systems Insight Display Systems Insight Display LEDsSystems Insight Display LED combinations RJ-45 LEDs for status Rear panel LEDs and buttonsPage Rear panel components Rear panel LEDs and buttons Non-hot-plug PCI riser board slot definitionsFL/FH System board components ItemDescriptionSystem maintenance switch Default FunctionNMI functionality Dimm slot locationsSAS and Sata device numbers Hot-plug drive LED definitions LEDPCI riser cage LED Fbwc module LEDs P420 Amber Green InterpretationHot-plug fans Page Operations Power up the serverPower down the server Extend the server from the rack Remove the access panel Install the access panelAccess the product rear panel Opening the cable management armPower down the server on Remove the hot-plug fan cageRemove the access panel on Remove the hot-plug fanRemove the full-length expansion board Remove the PCI riser cage Install the PCI riser cage Install the access panel onSecure the full-length expansion board retainer Remove the air baffle Page Setup Optional installation servicesOptimum environment Space and airflow requirementsElectrical grounding requirements Temperature requirementsPower requirements Connecting a DC power cable to a DC power source Rack warnings Identifying the contents of the server shipping cartonInstalling hardware options Installing the server into the rack Page VMware vSphere Installing the operating systemCitrix XenServer Powering on and selecting boot options Registering the serverMemory options Hardware options installationIntroduction HP SmartMemory Memory subsystem architectureSingle-, dual-, and quad-rank DIMMs Dimm identificationMemory configurations 1Maximum capacityAdvanced ECC memory configuration General Dimm slot population guidelines Advanced ECC population guidelinesInstalling a Dimm Lockstep Memory population guidelinesPower up the server on Hot-plug hard drive optionsInstalling a hot-plug SAS or Sata hard drive Controller options Removing a hot-plug SAS or Sata hard driveInstalling the flash-backed write cache module Installing the flash-backed write cache capacitor pack Page Remove the Velcro liner Hardware options installation Power up the server on Optical drive option 48V DC power supply option Page Page Page Page FlexibleLOM option FlexibleLOM option Expansion board options Removing the expansion slot blanksPage Installing a half-length expansion board Installing a full-length expansion board Secondary PCI riser cage option Page Install the secondary PCI riser cage 2U rack bezel option HP Trusted Platform Module optionInstalling the Trusted Platform Module board HP Trusted Platform Module option Retaining the recovery key/password Enabling the Trusted Platform ModuleCabling SAS hard drive cablingOptical drive cabling Fbwc cabling Chipset Sata cable option Remove the air baffle on Cabling PCIe power cable option HP product QuickSpecs Software and configuration utilitiesServer mode HP iLO Management Engine HP iLOIntelligent Provisioning Integrated Management LogHP Insight Remote Support software Erase UtilityScripting Toolkit HP Service Pack for ProLiant HP Smart Update ManagerHP ROM-Based Setup Utility Using RbsuConfiguring AMP modes Auto-configuration processBoot options Re-entering the server serial number and product ID Utilities and featuresArray Configuration Utility HP Smart Storage Administrator Option ROM Configuration for ArraysAutomatic Server Recovery ROMPaq utilityRedundant ROM support Keeping the system currentUSB support DriversSoftware and firmware Version control Change control and proactive notification Troubleshooting Troubleshooting resourcesBattery replacement Locate the battery System board components onPage Mechanical specifications SpecificationsEnvironmental specifications Power supply specificationsHP 1200 W CS HE Power Supply 94% efficiency Specification Value Input requirementsHP contact information Support and other resourcesBefore you contact HP Customer Self Repair Acronyms and abbreviations 101Acronyms and abbreviations Documentation feedback Index ASRIML
Top Page Image Contents