HP Z Virtual manual FlexibleLOM option

Page 66

FlexibleLOM option

WARNING! To reduce the risk of personal injury, electric shock, or damage to the equipment, remove the power cord to remove power from the server. The front panel Power On/Standby button does not completely shut off system power. Portions of the power supply and some internal circuitry remain active until AC power is removed.

1. Power down the server on page 18.

2. Remove all power:

a. Disconnect each power cord from the power source. b. Disconnect each power cord from the server.

3. Remove any attached network cables.

4. Extend the server from the rack on page 19.

5.Remove the access panel on page 20.

6.Loosen the thumbscrew.

7.Remove the existing FlexibleLOM.

To replace the component:

1. Firmly seat the FlexibleLOM in the slot, and then tighten the thumbscrew.

60 Chapter 5 Hardware options installation

Page 65 Page 67
Image 66
Page 65 Page 67
Contents HP DL380z Gen8 Virtual Workstation Part number First Edition April Table of contents Setup Active Health System Integrated Management Log 101 Abstract Component identification Front panel componentsFront panel LEDs and buttons Description StatusAccess the Systems Insight Display Systems Insight Display LEDsSystems Insight Display LED combinations RJ-45 LEDs for status Rear panel LEDs and buttonsPage Rear panel components Rear panel LEDs and buttons Non-hot-plug PCI riser board slot definitionsFL/FH System board components ItemDescriptionSystem maintenance switch Default FunctionNMI functionality Dimm slot locationsSAS and Sata device numbers Hot-plug drive LED definitions LEDPCI riser cage LED Fbwc module LEDs P420 Amber Green InterpretationHot-plug fans Page Power up the server Power down the serverOperations Extend the server from the rack Remove the access panel Install the access panelAccess the product rear panel Opening the cable management armPower down the server on Remove the hot-plug fan cageRemove the access panel on Remove the hot-plug fanRemove the full-length expansion board Remove the PCI riser cage Install the PCI riser cage Install the access panel onSecure the full-length expansion board retainer Remove the air baffle Page Setup Optional installation servicesOptimum environment Space and airflow requirementsTemperature requirements Power requirementsElectrical grounding requirements Connecting a DC power cable to a DC power source Identifying the contents of the server shipping carton Installing hardware optionsRack warnings Installing the server into the rack Page Installing the operating system Citrix XenServerVMware vSphere Powering on and selecting boot options Registering the serverHardware options installation IntroductionMemory options HP SmartMemory Memory subsystem architectureSingle-, dual-, and quad-rank DIMMs Dimm identificationMemory configurations 1Maximum capacityAdvanced ECC memory configuration General Dimm slot population guidelines Advanced ECC population guidelinesInstalling a Dimm Lockstep Memory population guidelinesPower up the server on Hot-plug hard drive optionsInstalling a hot-plug SAS or Sata hard drive Controller options Removing a hot-plug SAS or Sata hard driveInstalling the flash-backed write cache module Installing the flash-backed write cache capacitor pack Page Remove the Velcro liner Hardware options installation Power up the server on Optical drive option 48V DC power supply option Page Page Page Page FlexibleLOM option FlexibleLOM option Expansion board options Removing the expansion slot blanksPage Installing a half-length expansion board Installing a full-length expansion board Secondary PCI riser cage option Page Install the secondary PCI riser cage 2U rack bezel option HP Trusted Platform Module optionInstalling the Trusted Platform Module board HP Trusted Platform Module option Retaining the recovery key/password Enabling the Trusted Platform ModuleCabling SAS hard drive cablingOptical drive cabling Fbwc cabling Chipset Sata cable option Remove the air baffle on Cabling PCIe power cable option Software and configuration utilities Server modeHP product QuickSpecs HP iLO Management Engine HP iLOIntelligent Provisioning Integrated Management LogHP Insight Remote Support software Erase UtilityScripting Toolkit HP Service Pack for ProLiant HP Smart Update ManagerHP ROM-Based Setup Utility Using RbsuAuto-configuration process Boot optionsConfiguring AMP modes Utilities and features Array Configuration UtilityRe-entering the server serial number and product ID HP Smart Storage Administrator Option ROM Configuration for ArraysAutomatic Server Recovery ROMPaq utilityRedundant ROM support Keeping the system currentUSB support DriversSoftware and firmware Version control Change control and proactive notification Troubleshooting Troubleshooting resourcesBattery replacement Locate the battery System board components onPage Mechanical specifications SpecificationsEnvironmental specifications Power supply specificationsHP 1200 W CS HE Power Supply 94% efficiency Specification Value Input requirementsSupport and other resources Before you contact HPHP contact information Customer Self Repair Acronyms and abbreviations 101Acronyms and abbreviations Documentation feedback Index ASRIML
Top Page Image Contents