HP Z Virtual manual

Page 64

5. Attach the ground (earthed) wire to the ground screw and washer and tighten to 1.47 N m (13 lb- in) of torque. The ground wire must be connected before the positive or negative lead wires.

6. Attach the power ring tongues to the terminal block, following the polarity label below the terminal block, and then tighten the screws to 1.47 N m (13 lb-in) of torque.

58 Chapter 5 Hardware options installation

Image 64

Contents HP DL380z Gen8 Virtual Workstation Part number First Edition April Table of contents Setup Active Health System Integrated Management Log 101 Abstract Component identification Front panel componentsFront panel LEDs and buttons Description StatusAccess the Systems Insight Display Systems Insight Display LEDsSystems Insight Display LED combinations RJ-45 LEDs for status Rear panel LEDs and buttonsPage Rear panel components Rear panel LEDs and buttons Non-hot-plug PCI riser board slot definitionsFL/FH System board components ItemDescriptionSystem maintenance switch Default FunctionNMI functionality Dimm slot locationsSAS and Sata device numbers Hot-plug drive LED definitions LEDPCI riser cage LED Fbwc module LEDs P420 Amber Green InterpretationHot-plug fans Page Power down the server Power up the serverOperations Extend the server from the rack Remove the access panel Install the access panelAccess the product rear panel Opening the cable management armPower down the server on Remove the hot-plug fan cageRemove the access panel on Remove the hot-plug fanRemove the full-length expansion board Remove the PCI riser cage Install the PCI riser cage Install the access panel onSecure the full-length expansion board retainer Remove the air baffle Page Setup Optional installation servicesOptimum environment Space and airflow requirementsPower requirements Temperature requirementsElectrical grounding requirements Connecting a DC power cable to a DC power source Installing hardware options Identifying the contents of the server shipping cartonRack warnings Installing the server into the rack Page Citrix XenServer Installing the operating systemVMware vSphere Powering on and selecting boot options Registering the serverIntroduction Hardware options installationMemory options HP SmartMemory Memory subsystem architectureSingle-, dual-, and quad-rank DIMMs Dimm identificationMemory configurations 1Maximum capacityAdvanced ECC memory configuration General Dimm slot population guidelines Advanced ECC population guidelinesInstalling a Dimm Lockstep Memory population guidelinesPower up the server on Hot-plug hard drive optionsInstalling a hot-plug SAS or Sata hard drive Controller options Removing a hot-plug SAS or Sata hard driveInstalling the flash-backed write cache module Installing the flash-backed write cache capacitor pack Page Remove the Velcro liner Hardware options installation Power up the server on Optical drive option 48V DC power supply option Page Page Page Page FlexibleLOM option FlexibleLOM option Expansion board options Removing the expansion slot blanksPage Installing a half-length expansion board Installing a full-length expansion board Secondary PCI riser cage option Page Install the secondary PCI riser cage 2U rack bezel option HP Trusted Platform Module optionInstalling the Trusted Platform Module board HP Trusted Platform Module option Retaining the recovery key/password Enabling the Trusted Platform ModuleCabling SAS hard drive cablingOptical drive cabling Fbwc cabling Chipset Sata cable option Remove the air baffle on Cabling PCIe power cable option Server mode Software and configuration utilitiesHP product QuickSpecs HP iLO Management Engine HP iLOIntelligent Provisioning Integrated Management LogHP Insight Remote Support software Erase UtilityScripting Toolkit HP Service Pack for ProLiant HP Smart Update ManagerHP ROM-Based Setup Utility Using RbsuBoot options Auto-configuration processConfiguring AMP modes Array Configuration Utility Utilities and featuresRe-entering the server serial number and product ID HP Smart Storage Administrator Option ROM Configuration for ArraysAutomatic Server Recovery ROMPaq utilityKeeping the system current USB supportRedundant ROM support DriversSoftware and firmware Version control Change control and proactive notification Troubleshooting Troubleshooting resourcesBattery replacement Locate the battery System board components onPage Specifications Environmental specificationsMechanical specifications Power supply specificationsHP 1200 W CS HE Power Supply 94% efficiency Specification Value Input requirementsBefore you contact HP Support and other resourcesHP contact information Customer Self Repair Acronyms and abbreviations 101Acronyms and abbreviations Documentation feedback Index ASRIML