HP Z Virtual manual Power up the server on

Page 59

b. Install the FBWC capacitor pack holder into the server.

11. Install the access panel on page 20.

12. Install the server into the rack (Installing the server into the rack on page 35).

13.Connect each power cord to the server.

14. Connect each power cord to the power source.

15. Power up the server on page 18.

Controller options 53

Image 59

Contents HP DL380z Gen8 Virtual Workstation Part number First Edition April Table of contents Setup Active Health System Integrated Management Log 101 Abstract Front panel components Component identificationDescription Status Front panel LEDs and buttonsSystems Insight Display LEDs Access the Systems Insight DisplayRJ-45 LEDs for status Rear panel LEDs and buttons Systems Insight Display LED combinationsPage Rear panel components Non-hot-plug PCI riser board slot definitions Rear panel LEDs and buttonsFL/FH ItemDescription System board componentsDefault Function System maintenance switchDimm slot locations NMI functionalityLED SAS and Sata device numbers Hot-plug drive LED definitionsPCI riser cage LED Amber Green Interpretation Fbwc module LEDs P420Hot-plug fans Page Operations Power up the serverPower down the server Extend the server from the rack Install the access panel Remove the access panelOpening the cable management arm Access the product rear panelRemove the hot-plug fan cage Power down the server onRemove the hot-plug fan Remove the access panel onRemove the full-length expansion board Remove the PCI riser cage Install the access panel on Install the PCI riser cageSecure the full-length expansion board retainer Remove the air baffle Page Optional installation services SetupSpace and airflow requirements Optimum environmentElectrical grounding requirements Temperature requirementsPower requirements Connecting a DC power cable to a DC power source Rack warnings Identifying the contents of the server shipping cartonInstalling hardware options Installing the server into the rack Page VMware vSphere Installing the operating systemCitrix XenServer Registering the server Powering on and selecting boot optionsMemory options Hardware options installationIntroduction Memory subsystem architecture HP SmartMemoryDimm identification Single-, dual-, and quad-rank DIMMs1Maximum capacity Memory configurationsAdvanced ECC memory configuration Advanced ECC population guidelines General Dimm slot population guidelinesLockstep Memory population guidelines Installing a DimmHot-plug hard drive options Power up the server onInstalling a hot-plug SAS or Sata hard drive Removing a hot-plug SAS or Sata hard drive Controller optionsInstalling the flash-backed write cache module Installing the flash-backed write cache capacitor pack Page Remove the Velcro liner Hardware options installation Power up the server on Optical drive option 48V DC power supply option Page Page Page Page FlexibleLOM option FlexibleLOM option Removing the expansion slot blanks Expansion board optionsPage Installing a half-length expansion board Installing a full-length expansion board Secondary PCI riser cage option Page Install the secondary PCI riser cage HP Trusted Platform Module option 2U rack bezel optionInstalling the Trusted Platform Module board HP Trusted Platform Module option Enabling the Trusted Platform Module Retaining the recovery key/passwordSAS hard drive cabling CablingOptical drive cabling Fbwc cabling Chipset Sata cable option Remove the air baffle on Cabling PCIe power cable option HP product QuickSpecs Software and configuration utilitiesServer mode HP iLO HP iLO Management EngineIntegrated Management Log Intelligent ProvisioningErase Utility HP Insight Remote Support softwareScripting Toolkit HP Smart Update Manager HP Service Pack for ProLiantUsing Rbsu HP ROM-Based Setup UtilityConfiguring AMP modes Auto-configuration processBoot options Re-entering the server serial number and product ID Utilities and featuresArray Configuration Utility Option ROM Configuration for Arrays HP Smart Storage AdministratorROMPaq utility Automatic Server RecoveryDrivers Keeping the system currentUSB support Redundant ROM supportSoftware and firmware Version control Change control and proactive notification Troubleshooting resources TroubleshootingLocate the battery System board components on Battery replacementPage Power supply specifications SpecificationsEnvironmental specifications Mechanical specificationsSpecification Value Input requirements HP 1200 W CS HE Power Supply 94% efficiencyHP contact information Support and other resourcesBefore you contact HP Customer Self Repair 101 Acronyms and abbreviationsAcronyms and abbreviations Documentation feedback ASR IndexIML