HP Brocade 4Gb SAN c-Class BladeSystem manual Install the 4Gb SAN Switch

Page 24

Install the 4Gb SAN Switch

CAUTION:

For switch revision levels 0A and 0B only (running Fabric OS versions earlier than 5.2.1b) — DHCP is not supported on these models. Do not install multiple switches at the same time with default addresses, as address conﬂicts will occur. Locate switch revision levels on the switch or shipping carton. See Set the IP address.

For switch revision levels 0C and above only (Fabric OS 5.2.1b or later) — DHCP is supported and enabled by default for switches running Fabric OS 5.2.1b (switch rev 0C) or later. In this case, IP address conﬂicts will not occur during multiple switch installations. Locate switch revision levels on the switch or shipping carton. See Using External DHCP.

The Brocade 4Gb SAN switch is a hot-pluggable device. The enclosure power may be on or off when inserting the switch. Follow these steps to install the 4Gb SAN Switch.

1.Locate the appropriate interconnect bay in the rear of the enclosure per the appropriate HP BladeSystem Enclosure Setup and Installation Guide provided with your enclosure.

Remove the slot cover (if installed).

IMPORTANT:

Populate all enclosure I/O bays with the appropriate component (for example a switch, Pass-Thru or one of the blank panels provided with the enclosure).

CAUTION:

Properly ground yourself before handling the switch.

2.Press the handle latch to release the installation handle. See Figure 4.

24Setup

Image 24

Contents AA-RWEBB-TE Page Contents Managing the 4Gb SAN Switch Regulatory compliance and safetyPost SAN Switch technical speciﬁcations How to prevent electrostatic discharge Grounding methodsElectrostatic discharge Glossary IndexFigures Tables Page SAN Switch related documentation About this guideIntended audience HP c-Class BladeSystem related documentationBefore you contact HP Technical Support HP contact informationDocument conventions and symbols Document conventionsConvention Element Subscription service Other HP web sitesTIP Overview 4Gb SAN Switch features Identify the physical components of the 4Gb SAN Switch Component identiﬁcationInternal ports summary Item number Description4Gb SAN Switch redundancy 4Gb SAN Switch licensing Supported optional features ISL trunking groupsAccessory Part number Optional hardware kitsOptional hardware Setup Shipping carton contentsInstallation and safety considerations Installing multiple switchesIdentiﬁes 4Gb SAN switch components Electrical considerations Environmental considerationsInstall the 4Gb SAN Switch Scale 2/3 = OA veriﬁes power Verifying power-on LEDs Power-on LEDs Checking LEDsSetting the IP address Using Enclosure Bay IP Addressing EbipaUsing External Dhcp Setting the IP address manuallyConnect interconnect Conﬁgure the 4Gb SAN Switch Items required for conﬁgurationConnecting to the Command Line Interface Setting the date and time Verifying installed licenses ExampleModifying the FC domain ID optional Enter a unique domain ID. For exampleDisabling and enabling a switch Disabling and enabling a portUsing Dynamic Ports On Demand Dpod Dpod commandsExample for Brocade 4/12 SAN Switch Verifying the conﬁguration Backing up the conﬁguration40Setup Managing the 4Gb SAN Switch Management features4Gb SAN Switch management features Management tool Out-of-band support In-band supportMaintaining the 4Gb SAN Switch Installing dust covers in empty portsConnecting via a management station Replacing an SFP transceiverDiagnostic tests Installing an SFP SFP componentsPowering on and off Interpreting LED activityLED indicators Description LED indicators NumberSystem and power LED patterns are shown in Table LED patternsModule status LED patterns Module Status LED patterns during normal operationPort link status LED patterns Port link status LED patternsPost and boot speciﬁcations BootPort link speed LED patterns Interpreting Post results Firmware update About the reset button Rebooting the switchReplacing a faulty 4Gb SAN Switch Save the conﬁguration ﬁle Regulatory compliance and safety Regulatory complianceRegulatory compliance identiﬁcation numbers Laser deviceInternational notices and statements Canadian notice avis CanadienEuropean Union notice Bsmi noticeJapanese notice Korean notices Safety Battery replacement noticeTaiwan battery recycling notice Power cordsJapanese power cord statement Waste Electrical and Electronic Equipment directive English noticeDutch notice Czechoslovakian notice Estonian noticeFinnish notice French noticeGerman notice Greek noticeHungarian notice Italian noticeLatvian notice Lithuanian noticePolish notice Portuguese noticeSlovakian notice Slovenian noticeSpanish notice Swedish noticeHow to prevent electrostatic discharge Electrostatic dischargeGrounding methods This appendix provides the following informationElectrostatic discharge SAN Switch technical speciﬁcations General speciﬁcations General speciﬁcationsSpeciﬁcation Description Weight and physical dimensions 4Gb SAN Switch physical dimensionsDimension Measurement Lists physical propertiesEnvironmental requirements Supported SFPsSupported HBAs Environmental requirementsGlossary AlpaAPI AwtovCRC DLSEdtov Fcia FCPFlogi FRU FSPFspf LIP LmtovLpsm LWL MIBPlogi RatovRAID RrtovRscn SANSWL WWN86Glossary Index ISLTrunking groups LEDTransceiver, 14, 16, 31, 44, 47