HP Security Camera ML100 manual Laser compliance, Battery replacement notice

Page 100

Class B equipment

Laser compliance

This product may be provided with an optical storage device (that is, CD or DVD drive) and/or fiber optic transceiver. Each of these devices contains a laser that is classified as a Class 1 Laser Product in accordance with US FDA regulations and the IEC 60825-1. The product does not emit hazardous laser radiation.

Each laser product complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007; and with IEC 60825-1:2007.

WARNING: Use of controls or adjustments or performance of procedures other than those specified herein or in the laser product's installation guide may result in hazardous radiation exposure. To reduce the risk of exposure to hazardous radiation:

Do not try to open the module enclosure. There are no user-serviceable components inside.

Do not operate controls, make adjustments, or perform procedures to the laser device other than those specified herein.

Allow only HP Authorized Service technicians to repair the unit.

The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration implemented regulations for laser products on August 2, 1976. These regulations apply to laser products manufactured from August 1, 1976. Compliance is mandatory for products marketed in the United States.

Battery replacement notice

WARNING: The computer contains an internal lithium manganese dioxide, a vanadium pentoxide, or an alkaline battery pack. A risk of fire and burns exists if the battery pack is not properly handled. To reduce the risk of personal injury:

Do not attempt to recharge the battery.

Do not expose the battery to temperatures higher than 60°C (140°F).

Do not disassemble, crush, puncture, short external contacts, or dispose of in fire or water.

Batteries, battery packs, and accumulators should not be disposed of together with the general household waste. To forward them to recycling or proper disposal, use the public collection system or return them to HP, an authorized HP Partner, or their agents.

For more information about battery replacement or proper disposal, contact an authorized reseller or an authorized service provider.

Taiwan battery recycling notice

The Taiwan EPA requires dry battery manufacturing or importing firms in accordance with Article 15 of the Waste Disposal Act to indicate the recovery marks on the batteries used in sales, giveaway or promotion. Contact a qualified Taiwanese recycler for proper battery disposal.

Regulatory compliance notices 100

Image 100
Contents HP ProLiant ML100 Series Server User Guide Page Contents Troubleshooting Support and other resources 103 Power down the server Power up the serverServer operations Server setup Optional installation servicesRack planning resources Optimum environmentTemperature requirements Rack warnings Power requirementsElectrical grounding requirements Installing hardware options Powering up and configuring the serverInstalling the operating system Registering the serverHardware options installation Access panelIntroduction Processor optionHardware options installation Hardware options installation Hardware options installation Hardware options installation Hardware options installation Hardware options installation Hardware options installation Hardware options installation SAS or Sata hard drive options Remove the hard drive blank Prepare the hard drive Hard drive LED cable option Installing the LED cable ML110 G4 Hardware options installation Hardware options installation Installing the LED cable ML150 G3 Hardware options installation Installing the LED cable ML110 G5, ML115 G5, and ML150 G5 Connector locations ML110 G5, ML115 G5, and ML150 G5Hardware options installation Hardware options installation HP Smart Array E200 controller card Hardware options installation Installing media devices with rails Removable media device optionsInstalling media devices with screws Hardware options installation Installing media devices with a media latch Installing media devices with wire retainers Installing a half-height media deviceInstalling a full-height media device Hardware options installation Installing DIMMs Interleaving and non-interleaving memory configurationMemory options Installing an expansion board with a single retainer Expansion board optionsHardware options installation Installing an expansion board with individual retainers Installing an expansion board with an external retainer Hardware options installation Hardware options installation Server software and configuration utilities HP Insight DiagnosticsROMPaq utility Keeping the system currentEmbedded Sata RAID feature Required hardwareDiskette and CD-ROM drive options HP Integrated Lights-Out Virtual Floppy and CD-ROM drivesEnabling Sata RAID functionality in the Bios Setup Utility Configuring the Sata RAID featureProLiant ML110 Generation 3 Server ProLiant ML150 Generation 5 Servers Creating a RAID volume ProLiant ML115 and ML115 G5 ServersUSB diskette and CD-ROM drives DOSInstalling a supported Microsoft Windows OS Installing an operating systemInstalling a supported Linux or NetWare OS Troubleshooting Pre-diagnostic stepsImportant safety information Important safety informationTroubleshooting Symptom information Preparing the server for diagnosisService notifications Firmware updates Common problem resolutionLoose connections Dimm handling guidelines Hard drive guidelinesSAS and Sata hard drive guidelines Scsi hard drive guidelinesHot-plug Scsi hard drive LED combinations SAS and Sata hard drive LED combinationsTroubleshooting flowcharts Start diagnosis flowchartGeneral diagnosis flowchart SeeGeneral memory problems are occurring on Power-on problems flowchart Support CD, or the HP website Post problems flowchart Symptom information on OS boot problems flowchart Server fault indications flowchart Support CD, or the HP website Hardware problems Power problems Power source problemsPower supply problems UPS problemsGeneral hardware problems Problems with new hardwareLow battery warning is displayed One or more LEDs on the UPS is redUnknown problem Internal system problems Third-party device problemsCD-ROM and DVD drive problems Testing the deviceDrive is not detected DAT drive problemsDAT drive is providing poor performance Diskette drive problems DLT drive problems Server cannot write to tapeDLT drive failure occurs DLT drive does not read tapeFan problems Hard drive problemsAn error occurs during backup, but the backup is completed General fan problems are occurringData is inaccessible No hard drives are recognizedHard drive is not recognized by the server New hard drive is not recognizedMemory problems General memory problems are occurringMemory count error exists Server response time is slower than usualPPM problems Processor problemsServer fails to recognize existing memory Server fails to recognize new memoryVideo problems External device problemsSystem open circuits and short circuits Video colors are wrong Audio problemsSlow-moving horizontal lines are displayed Mouse and keyboard problems Printer problemsModem problems No response occurs when you type AT commands AT commands are not visibleModem does not answer an incoming call Modem does not connect to another modemNetwork controller problems Network controller has stopped working Software problems Operating system problemsWhen to reconfigure or reload software Operating system updatesRestoring to a backed-up version Firmware maintenance Linux operating systems Application software problemsAutomatic backup Types of ROMROMPaq utility diskette or USB drive key System ROMROMPaq Disaster Recovery Current firmware versionsUpdating firmware Battery replacement Regulatory compliance identification numbers Regulatory compliance noticesFederal Communications Commission notice Cables ModificationsCanadian notice Avis Canadien European Union regulatory notice Japanese notice Bsmi notice Korean notice Taiwan battery recycling notice Battery replacement noticeLaser compliance Regulatory compliance notices Preventing electrostatic discharge Electrostatic dischargeGrounding methods to prevent electrostatic discharge Support and other resources Before you contact HPHP contact information Customer Self RepairRéparation par le client CSR Riparazione da parte del cliente Reparaciones del propio cliente Reparo feito pelo cliente Support and other resources Support and other resources Support and other resources LO100 Acronyms and abbreviationsPCI Express PDU Documentation feedback Index Installing operating system Temperature requirements