HP R7000 manual Support and other resources, Before you contact HP, HP contact information

Page 58

Support and other resources

Before you contact HP

Be sure to have the following information available before you call HP:

Active Health System log (HP ProLiant Gen8 or later products)

Download and have available an Active Health System log for 3 days before the failure was detected. For more information, see the HP iLO 4 User Guide or HP Intelligent Provisioning User Guide on the HP website (http://www.hp.com/go/ilo/docs).

Onboard Administrator SHOW ALL report (for HP BladeSystem products only)

For more information on obtaining the Onboard Administrator SHOW ALL report, see the HP website (http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&objectID=c 02843807).

Technical support registration number (if applicable)

Product serial number

Product model name and number

Product identification number

Applicable error messages

Add-on boards or hardware

Third-party hardware or software

Operating system type and revision level

HP contact information

For United States and worldwide contact information, see the Contact HP website (http://www.hp.com/go/assistance).

In the United States:

To contact HP by phone, call 1-800-334-5144. For continuous quality improvement, calls may be recorded or monitored.

If you have purchased a Care Pack (service upgrade), see the Support & Drivers website

(http://www8.hp.com/us/en/support-drivers.html). If the problem cannot be resolved at the website, call 1-800-633-3600. For more information about Care Packs, see the HP website (http://pro-aq-sama.houston.hp.com/services/cache/10950-0-0-225-121.html).

Support and other resources 58

Image 58
Contents HP UPS R7000 User Guide Part Number February EditionPage Contents Maintenance Power Protector softwareSpares Overview Important safety informationUPS R7000 features UPS R7000 overviewUPS front panel controls Component identificationUPS front panel DescriptionUPS rear panel Repo port ERM rear panel Preparing to install the hardware Installation and configurationPrecautions Tools and materialsReadying the equipment Installing the mounting railsSelecting a site Hex nuts Cage nuts Cage nut-fitting toolInstallation and configuration Installation and configuration Installation and configuration Preparing the rails for integrated shipping Installing the UPS Connecting the battery leadsInstallation and configuration Configuring a USB to serial converter Reassigning the USB COM ports Installation and configuration Installation and configuration Connecting the ground bonding cable Connecting the network cableConnecting the UPS to utility power Connecting devices to the UPSStarting power to the load Configuring the UPS Network ModuleConnecting the configuration cable Be sure that the UPS is powered on Configuring the UPS Network Module network settingsLaunching a terminal emulation program Accessing the web interface Installing the ERM Configuring the UPS Network Module settingsAttaching the ERM front bezel Connecting the ERM to the UPS Charging the ERM batteriesAuto-Bypass mode Standby modeOperate mode UPS operationsChanging the language Configuring the UPSChanging display functions After connecting the Repo port on Verifying the Repo port connectionPowering down the UPS Power management Power Protector softwarePower management Maintenance Important battery safety information Replacing the batteriesBattery care and storage guidelines UPS battery replacement procedureMaintenance Replacing the UPS Disconnect the battery leads Remove the UPS battery bracket Replacing the ERM Updating the UPS firmwareTroubleshooting Alarm troubleshootingAlarm number Alarm name Alarm description Alarm type Silencing an audible alarm Battery connection conditionGeneral alarm condition Bypass is out of rangeInput voltage is out of range Internal UPS fault conditionLow battery shutdowns Insufficient warning of low batteriesUPS frequently switches between utility and battery power Site wiring conditionUPS does not provide the expected backup time Repo conditionUtility power condition UPS is in Auto-Bypass modeUPS is on battery UPS is on bypassERM physical specifications SpecificationsUPS physical specifications UPS input specificationsOutput tolerance specifications Power protection specificationsVoltage specifications Output feature specificationsAverage battery runtime Battery specificationsMinimum battery runtime Environmental specifications Repo port specificationsOrdering spares UPS spare parts listSpares Hardware options$250,000 Computer Load Protection Guarantee Safety and regulatory complianceWarranty information Limited warranty Regulatory informationPre-Failure Battery Warranty Recommended duration of usePreventing electrostatic discharge Electrostatic dischargeGrounding methods to prevent electrostatic discharge Before you contact HP Support and other resourcesHP contact information Acronyms and abbreviations Documentation feedback Index Index