HP R7000 manual Verifying the Repo port connection, After connecting the Repo port on

Page 33

Main menu	Submenu	Display information or menu function

—	Battery status	Battery Charging/Floating/Resting, Charge
		Level, ERM Number, and Runtime
Event Log	—	Displays events and alarms
Measurements	Output	Output watts and VA
—	Output	Output amps and power factor
—	Output	Output voltage and frequency
—	Input	Input voltage and frequency

—	Battery	Battery voltage and percent charge
Control	Go to Bypass mode	Transfers the UPS system to internal Bypass
		mode
		When this command is active, the option
		changes to Go to Normal mode.

—	Battery Test	Schedules a battery test

—	Reset error state	Reset alarms

—	Load segments	Turns load segments on or off

—	Restore factory settings	Resets the UPS back to factory settings
Settings	Change language	Changes language settings. The default is
		English.

—	User Password	Enables or disables password. Default: Disable.
		If Enable is selected, the password is USER. The
		password cannot be changed.

—	Set date and time	Sets date and time
—	Control commands from serial	Enables or disables serial port control
	port	commands. Default: Enabled
—	Output voltage	Sets output voltage
—	Auto start delay	Selects load segment and delay time in seconds
—	Automatic on battery shutdown	Selects load segment and delay time in seconds
—	On battery notice delay	Sets delay time in seconds
—	Site wiring fault alarm	Enables or disables site wiring fault alarm. The
		default is Disabled
—	Battery low alarm	Sets battery low alarm. Default: 3 minutes.
—	Automatic battery test	Enables or disables battery test. Default:
		Disabled

—	LCD contrast	Change LCD contrast. Default: +0
Identification	—	UPS Type / Part Number / Serial Number /
		NMC Firmware / Comm Firmware / UPS
		Firmware

Verifying the REPO port connection

NOTE: While testing, operate connected equipment in a safe test mode so the effects do not disrupt critical operations.

After connecting the REPO port (on page 21):

UPS operations 33

Image 33

Contents Part Number February Edition HP UPS R7000 User GuidePage Contents Power Protector software MaintenanceSpares UPS R7000 features Important safety informationOverview UPS R7000 overviewUPS front panel Component identificationUPS front panel controls DescriptionUPS rear panel Repo port ERM rear panel Precautions Installation and configurationPreparing to install the hardware Tools and materialsSelecting a site Installing the mounting railsReadying the equipment Hex nuts Cage nuts Cage nut-fitting toolInstallation and configuration Installation and configuration Installation and configuration Preparing the rails for integrated shipping Connecting the battery leads Installing the UPSInstallation and configuration Configuring a USB to serial converter Reassigning the USB COM ports Installation and configuration Installation and configuration Connecting the network cable Connecting the ground bonding cableConnecting devices to the UPS Connecting the UPS to utility powerConfiguring the UPS Network Module Starting power to the loadConnecting the configuration cable Configuring the UPS Network Module network settings Be sure that the UPS is powered onLaunching a terminal emulation program Accessing the web interface Configuring the UPS Network Module settings Installing the ERMAttaching the ERM front bezel Charging the ERM batteries Connecting the ERM to the UPSOperate mode Standby modeAuto-Bypass mode UPS operationsConfiguring the UPS Changing the languageChanging display functions Verifying the Repo port connection After connecting the Repo port onPowering down the UPS Power Protector software Power managementPower management Maintenance Replacing the batteries Important battery safety informationUPS battery replacement procedure Battery care and storage guidelinesMaintenance Replacing the UPS Disconnect the battery leads Remove the UPS battery bracket Updating the UPS firmware Replacing the ERMAlarm troubleshooting TroubleshootingAlarm number Alarm name Alarm description Alarm type General alarm condition Battery connection conditionSilencing an audible alarm Bypass is out of rangeLow battery shutdowns Internal UPS fault conditionInput voltage is out of range Insufficient warning of low batteriesUPS does not provide the expected backup time Site wiring conditionUPS frequently switches between utility and battery power Repo conditionUPS is on battery UPS is in Auto-Bypass modeUtility power condition UPS is on bypassUPS physical specifications SpecificationsERM physical specifications UPS input specificationsVoltage specifications Power protection specificationsOutput tolerance specifications Output feature specificationsBattery specifications Average battery runtimeMinimum battery runtime Repo port specifications Environmental specificationsSpares UPS spare parts listOrdering spares Hardware optionsWarranty information Limited warranty Safety and regulatory compliance$250,000 Computer Load Protection Guarantee Regulatory informationRecommended duration of use Pre-Failure Battery WarrantyElectrostatic discharge Preventing electrostatic dischargeGrounding methods to prevent electrostatic discharge Support and other resources Before you contact HPHP contact information Acronyms and abbreviations Documentation feedback Index Index