HP A165890669 manual Preparing to Install the CD±ROM Drive, Tools Required, Verifying Kit Contents

Page 16

Introduction

Preparing to Install the CD±ROM Drive

The following information is provided to prepare the CD±ROM for installation.

Tools Required

The following tools are needed to install the CD±ROM drive:

•#2 Phillips screwdriver

•Small needle±nose pliers

Verifying Kit Contents

Verify that the kit contains one of each of the following:

•CD±ROM drive (drive P/N A4325±60001)

•Set of 4 screws (M4x6)

•Power adapter cable

•SCSI I/O cable

•Static strap

•HP 4x Speed CD±ROM Disk Drive User's Guide (A1658±90669)

NOTICE: If any contents of your kit are missing, contact your sales representative.

Minimum Requirements

Minimum requirement for the HP±UX operating system is level 9.03 for the HP 4x Speed CD±ROM drive.

NOTICE: You must use software patch PHSS_5764 under HP±UX 9.03, 9.05 and 9.07 to run SupportWave successfully.

1±6

Image 16

Contents HP 4x Speed CD±ROM Disk Drive Users Guide 10 9 8 7 6 5 4 3 2 Contents Using your CD±ROM Drive Maintenance and TroubleshootingAppendix a Safety and Regulatory Statements Appendix B Scsi Connector PinoutFigures Safety and Regulatory Statements AudienceInstallation Notice Related ManualsProblems, Questions, and Suggestions Revision HistoryEdition E0895 First PrintingDocumentation Conventions Literal valuesChapter General Description ±1. HP 4x Speed CD±ROM DriveMajor Features of the CD±ROM Drive Temperature CD±ROM Drive Environmental RequirementsAltitude HumidityCD±ROM Drive Physical Specifications ±2. HP 4x Speed CD±ROM Physical SpecificationsPreparing to Install the CD±ROM Drive Verifying Kit ContentsTools Required Minimum RequirementsSet the SCSI±2 Address Address Jumpers ±3. SCSI±2 Address Settings Etc/ioscan ±d scsi Return Prepare the SystemUsr/sbin/ioscan ±d sdisk Return Ioscan No hardware found # /etc/shutdown ±h Return Single-Ended SCSI-2 Bus Configuration Constraints Type of Device Allowed Single-Ended SCSI-2 DevicesMaximum Number of SCSI-2 Devices per bus SCSI-2 Bus Termination Guidelines Power Off the Workstation and any Peripherals Using Your CD±ROM Drive Scsi ID and Device File Information for HP±UX Your CD±ROM Drive ConfigurationDevice Controls and Features of the CD±ROM Drive ±1. CD±ROM Drive Controls and FeaturesControl/Feature Purpose Using the CD±ROM Drive Media DescriptionDisc Tray Description ±2. CD±ROM Disc TrayLoading a CD±ROM Disc in a Horizontally Mounted Drive Unloading a CD±ROM Disc in a Horizontally Mounted Drive Loading a CD±ROM Disc in a Vertically Mounted Drive ±5. Inserting a CD±ROM Disc Vertical MountUnloading a CD±ROM Disc in a Vertically Mounted Drive ±10Mkdir /cdrom Return Mounting a CD±ROM Disc±11 Cd /cdrom Return Unmounting a CD±ROM Disc±12 ±13 Reading the Busy Light ±14Maintenance and Troubleshooting Caring for the CD±ROM Discs Check the Address Settings for Single±Ended Drives TroubleshootingEtc/ioscan Return Screen similar to the following appears Usr/sbin/ioscan ±d sdisk Return Check the Hardware Installation Recheck the Address Settings Verify the System Operation using SupportWave # man cstm Return # man mstm Return # man xstm ReturnFollowing screen appears Cstm verify all Return When you see the prompt shown above, type the following Removal and Replacement Procedures Field Replaceable UnitsRemoving and Replacing the CD±ROM Drive Description Part Number CD±ROM Drive A4325±60001Appendix a Federal Communications Commission FCC Emissions RegulationsCanadian Department of Communications CDC Acoustics Emissions Regulations ComplianceRegulation On Noise Declaration For Machines ±3. Gsgv Electrostatic Discharge ESD Precautions Laser Safety Statement For U.S.A. Only Laserturvallisuus Loukan 1 Laserlaite Klass 1 Laser ApparatIEC 825 Class Laser Labels Warnung Appendix B Order Number A1658±90669 Edition E0895