HP A165890669 manual Loading a CD±ROM Disc in a Horizontally Mounted Drive

Page 33

Using Your CD±ROM Drive

Loading a CD±ROM Disc in a Horizontally Mounted Drive

This CD±ROM drive has an automatic loading/ejecting feature. To load a disc in the CD±ROM drive, follow these steps:

1.Check that the workstation is powered on.

2.To open the Disc Tray, press and release the Load/Eject button on the CD±ROM drive.

3.Ensure the disc holders are held away from disc by the disc holder retainers.

4.Hold the disc by the edges with the label side up and place it in the Disc Tray as shown in Figure 2±3.

5.To close the Disc Tray, push the front of the disc tray gently towards the drive until it closes by itself or press the Load/Eject button.

Figure 2±3. Placing the CD±ROM Disc in the Disc Tray (Horizontal Mount)

2±7

Image 33

Contents HP 4x Speed CD±ROM Disk Drive Users Guide 10 9 8 7 6 5 4 3 2 Contents Maintenance and Troubleshooting Using your CD±ROM DriveAppendix B Scsi Connector Pinout Appendix a Safety and Regulatory StatementsFigures Audience Safety and Regulatory StatementsRelated Manuals Installation NoticeRevision History Problems, Questions, and SuggestionsEdition E0895 First PrintingLiteral values Documentation ConventionsChapter ±1. HP 4x Speed CD±ROM Drive General DescriptionMajor Features of the CD±ROM Drive CD±ROM Drive Environmental Requirements TemperatureAltitude Humidity±2. HP 4x Speed CD±ROM Physical Specifications CD±ROM Drive Physical SpecificationsVerifying Kit Contents Preparing to Install the CD±ROM DriveTools Required Minimum RequirementsSet the SCSI±2 Address Address Jumpers ±3. SCSI±2 Address Settings Prepare the System Etc/ioscan ±d scsi ReturnUsr/sbin/ioscan ±d sdisk Return Ioscan No hardware found # /etc/shutdown ±h Return Single-Ended SCSI-2 Bus Configuration Constraints Single-Ended SCSI-2 Devices Type of Device AllowedMaximum Number of SCSI-2 Devices per bus SCSI-2 Bus Termination Guidelines Power Off the Workstation and any Peripherals Using Your CD±ROM Drive Your CD±ROM Drive Configuration Scsi ID and Device File Information for HP±UXDevice ±1. CD±ROM Drive Controls and Features Controls and Features of the CD±ROM DriveControl/Feature Purpose Media Description Using the CD±ROM Drive±2. CD±ROM Disc Tray Disc Tray DescriptionLoading a CD±ROM Disc in a Horizontally Mounted Drive Unloading a CD±ROM Disc in a Horizontally Mounted Drive ±5. Inserting a CD±ROM Disc Vertical Mount Loading a CD±ROM Disc in a Vertically Mounted Drive±10 Unloading a CD±ROM Disc in a Vertically Mounted DriveMounting a CD±ROM Disc Mkdir /cdrom Return±11 Unmounting a CD±ROM Disc Cd /cdrom Return±12 ±13 ±14 Reading the Busy LightMaintenance and Troubleshooting Caring for the CD±ROM Discs Troubleshooting Check the Address Settings for Single±Ended DrivesEtc/ioscan Return Screen similar to the following appears Usr/sbin/ioscan ±d sdisk Return Check the Hardware Installation Recheck the Address Settings # man cstm Return # man mstm Return # man xstm Return Verify the System Operation using SupportWaveFollowing screen appears Cstm verify all Return When you see the prompt shown above, type the following Field Replaceable Units Removal and Replacement ProceduresRemoving and Replacing the CD±ROM Drive Description Part Number CD±ROM Drive A4325±60001Appendix a Emissions Regulations Federal Communications Commission FCCCanadian Department of Communications CDC Emissions Regulations Compliance AcousticsRegulation On Noise Declaration For Machines ±3. Gsgv Electrostatic Discharge ESD Precautions Laserturvallisuus Loukan 1 Laserlaite Klass 1 Laser Apparat Laser Safety Statement For U.S.A. OnlyIEC 825 Class Laser Labels Warnung Appendix B Order Number A1658±90669 Edition E0895