HP A165890669 manual Recheck the Address Settings

Page 47

CAUTION: Do not power off your workstation without first shutting down HP±UX. Powering off with HP±UX still running could damage the data on the disks associated with your workstation.

5.Remove the drive and check the jumpers, as described in Removal and Replacement Procedures at the end of this chapter.

6.Replace the drive.

7.Check the cable connections of your CD±ROM drive. Make sure that the connectors are aligned and seated correctly.

8.Recheck the device list (see the next section).

Recheck the Address Settings

Check the address settings again to see if the drive is now listed (see the ªCheck the Address Settingsº section, earlier in this chapter).

If the CD±ROM drive and all other SCSI±2 devices available to you before you installed the CD±ROM drive are now listed, run the system verification test for your software version, as explained in the next sections.

If the CD±ROM drive is still not listed, or one of the SCSI±2 devices available to you before you installed the CD±ROM drive is still not listed, contact your service representative.

3±7

Image 47

Contents HP 4x Speed CD±ROM Disk Drive Users Guide 10 9 8 7 6 5 4 3 2 Contents Maintenance and Troubleshooting Using your CD±ROM DriveAppendix B Scsi Connector Pinout Appendix a Safety and Regulatory StatementsFigures Audience Safety and Regulatory StatementsRelated Manuals Installation NoticeE0895 First Printing Problems, Questions, and SuggestionsRevision History EditionLiteral values Documentation ConventionsChapter ±1. HP 4x Speed CD±ROM Drive General DescriptionMajor Features of the CD±ROM Drive Humidity TemperatureCD±ROM Drive Environmental Requirements Altitude±2. HP 4x Speed CD±ROM Physical Specifications CD±ROM Drive Physical SpecificationsMinimum Requirements Preparing to Install the CD±ROM DriveVerifying Kit Contents Tools RequiredSet the SCSI±2 Address Address Jumpers ±3. SCSI±2 Address Settings Usr/sbin/ioscan ±d sdisk Return Prepare the SystemEtc/ioscan ±d scsi Return Ioscan No hardware found # /etc/shutdown ±h Return Single-Ended SCSI-2 Bus Configuration Constraints Maximum Number of SCSI-2 Devices per bus Single-Ended SCSI-2 DevicesType of Device Allowed SCSI-2 Bus Termination Guidelines Power Off the Workstation and any Peripherals Using Your CD±ROM Drive Device Your CD±ROM Drive ConfigurationScsi ID and Device File Information for HP±UX ±1. CD±ROM Drive Controls and Features Controls and Features of the CD±ROM DriveControl/Feature Purpose Media Description Using the CD±ROM Drive±2. CD±ROM Disc Tray Disc Tray DescriptionLoading a CD±ROM Disc in a Horizontally Mounted Drive Unloading a CD±ROM Disc in a Horizontally Mounted Drive ±5. Inserting a CD±ROM Disc Vertical Mount Loading a CD±ROM Disc in a Vertically Mounted Drive±10 Unloading a CD±ROM Disc in a Vertically Mounted Drive±11 Mounting a CD±ROM DiscMkdir /cdrom Return ±12 Unmounting a CD±ROM DiscCd /cdrom Return ±13 ±14 Reading the Busy LightMaintenance and Troubleshooting Caring for the CD±ROM Discs Etc/ioscan Return TroubleshootingCheck the Address Settings for Single±Ended Drives Screen similar to the following appears Usr/sbin/ioscan ±d sdisk Return Check the Hardware Installation Recheck the Address Settings # man cstm Return # man mstm Return # man xstm Return Verify the System Operation using SupportWaveFollowing screen appears Cstm verify all Return When you see the prompt shown above, type the following Description Part Number CD±ROM Drive A4325±60001 Removal and Replacement ProceduresField Replaceable Units Removing and Replacing the CD±ROM DriveAppendix a Canadian Department of Communications CDC Emissions RegulationsFederal Communications Commission FCC Regulation On Noise Declaration For Machines ±3. Gsgv Emissions Regulations ComplianceAcoustics Electrostatic Discharge ESD Precautions Laserturvallisuus Loukan 1 Laserlaite Klass 1 Laser Apparat Laser Safety Statement For U.S.A. OnlyIEC 825 Class Laser Labels Warnung Appendix B Order Number A1658±90669 Edition E0895