HP A165890669 manual Unloading a CD±ROM Disc in a Horizontally Mounted Drive

Page 34

Using Your CD±ROM Drive

Unloading a CD±ROM Disc in a Horizontally Mounted Drive

Perform the following steps to unload a disc from the CD±ROM drive:

1.Press the eject button to eject the disc tray from the drive. If the drive is in use, you must unmount the disc to eject the disc tray. The emergency eject feature allows you to eject the disc tray if the normal procedure fails. See Table 2±1.

NOTICE: You must unmount the disc before ejecting it from the drive. Refer to the subsection, ªUnmounting a CD±ROM Disc,º for instructions on unmounting a disc.

2.Wait until the drive has fully ejected the disc tray, then remove the disc from the tray as shown in Figure 2±4. Be careful to touch only the edges of the disc.

Figure 2±4. Removing the CD±ROM Disc From the Disc Tray (Horizontal Mount)

3.To close the Disc Tray, push the front of the disc tray gently towards the drive until it closes by itself.

2±8

Image 34

Contents HP 4x Speed CD±ROM Disk Drive Users Guide 10 9 8 7 6 5 4 3 2 Contents Using your CD±ROM Drive Maintenance and TroubleshootingAppendix a Safety and Regulatory Statements Appendix B Scsi Connector PinoutFigures Safety and Regulatory Statements AudienceInstallation Notice Related ManualsEdition Problems, Questions, and SuggestionsRevision History E0895 First PrintingDocumentation Conventions Literal valuesChapter General Description ±1. HP 4x Speed CD±ROM DriveMajor Features of the CD±ROM Drive Altitude TemperatureCD±ROM Drive Environmental Requirements HumidityCD±ROM Drive Physical Specifications ±2. HP 4x Speed CD±ROM Physical SpecificationsTools Required Preparing to Install the CD±ROM DriveVerifying Kit Contents Minimum RequirementsSet the SCSI±2 Address Address Jumpers ±3. SCSI±2 Address Settings Etc/ioscan ±d scsi Return Prepare the SystemUsr/sbin/ioscan ±d sdisk Return Ioscan No hardware found # /etc/shutdown ±h Return Single-Ended SCSI-2 Bus Configuration Constraints Type of Device Allowed Single-Ended SCSI-2 DevicesMaximum Number of SCSI-2 Devices per bus SCSI-2 Bus Termination Guidelines Power Off the Workstation and any Peripherals Using Your CD±ROM Drive Scsi ID and Device File Information for HP±UX Your CD±ROM Drive ConfigurationDevice Controls and Features of the CD±ROM Drive ±1. CD±ROM Drive Controls and FeaturesControl/Feature Purpose Using the CD±ROM Drive Media DescriptionDisc Tray Description ±2. CD±ROM Disc TrayLoading a CD±ROM Disc in a Horizontally Mounted Drive Unloading a CD±ROM Disc in a Horizontally Mounted Drive Loading a CD±ROM Disc in a Vertically Mounted Drive ±5. Inserting a CD±ROM Disc Vertical MountUnloading a CD±ROM Disc in a Vertically Mounted Drive ±10Mkdir /cdrom Return Mounting a CD±ROM Disc±11 Cd /cdrom Return Unmounting a CD±ROM Disc±12 ±13 Reading the Busy Light ±14Maintenance and Troubleshooting Caring for the CD±ROM Discs Check the Address Settings for Single±Ended Drives TroubleshootingEtc/ioscan Return Screen similar to the following appears Usr/sbin/ioscan ±d sdisk Return Check the Hardware Installation Recheck the Address Settings Verify the System Operation using SupportWave # man cstm Return # man mstm Return # man xstm ReturnFollowing screen appears Cstm verify all Return When you see the prompt shown above, type the following Removing and Replacing the CD±ROM Drive Removal and Replacement ProceduresField Replaceable Units Description Part Number CD±ROM Drive A4325±60001Appendix a Federal Communications Commission FCC Emissions RegulationsCanadian Department of Communications CDC Acoustics Emissions Regulations ComplianceRegulation On Noise Declaration For Machines ±3. Gsgv Electrostatic Discharge ESD Precautions Laser Safety Statement For U.S.A. Only Laserturvallisuus Loukan 1 Laserlaite Klass 1 Laser ApparatIEC 825 Class Laser Labels Warnung Appendix B Order Number A1658±90669 Edition E0895