HP 5000 Router manual Send File dialog box

Page 37

Introduction 35

Downloading ... CCCCC

After the baud rate at the console terminal is set, the new setting can become valid only if the terminal emulation program is disconnected and reconnected for at least once.

4Select [Transmit/send file] in the terminal window and the following dialog box will pop up:

Figure 24 Send File dialog box

5Click <Browse>, select the application file to be downloaded, and set the protocol to Xmodem. Then click <Send>, and the system will pop up the following interface:

Figure 25 Sending file interface

6After completing download, the system begins writing to Flash (Flash memory), then the following information will be displayed in the terminal interface, indicating that the download has been completed:

Download completed.

Writing to flash memory...

Please wait,it needs a long time .Please wait...

########################################################

Writing FLASH Success.

Image 37
Contents Router 5000 Family Installation Guide Campus Drive 3Com CorporationMarlborough, MA 01752-3064Contents Troubleshooting Conventions About this GuideProtocols that are used to interconnect WANs List conventions that are used throughout this guideDocumentation RelatedIntroducing the Router Family Router 5000 Family Router 5000 Family Console Port SpecificationsHardware Fixed portsGround Lists the attributes of the Router 5000 Family AUX portLEDs Table below describes the LEDs on the Router Router 5232, 5642, 5682 LEDs Describes the LEDs on the Router 5232, 5642, 5682 routersFront View of the Router System Specifications for the RouterDescription Attribute Synchronous Asynchronous Synchronous/Asynchronous Serial Port SpecificationsRouter 5642 specifications Router 5232 specificationsRouter 5682 specifications System Specifications for the Router Introducing the Router 5000 Family Installing the Router Specification for Dust Content Temperature and HumidityDust GasesLightning Damage Electromagnetic DischargeA Rack Mounting the RouterConnecting the Power Installing the RouterConnecting the Router On the WorkbenchInstalling SICs and MIMs That uses category-5 twisted pair cable To the EthernetFixed Ethernet cables are supplied with the router Use shielded cables to ensure electromagnetic compatibilityPort to a CSU/DSU Connecting the AUX Port to the Analog ModemVerifying Installing the Router Connecting the Router to a Remote Console Terminal Booting and Configuring RouterConnector to the serial port of a PC, as shown below To a Local ConsoleParameters Console Terminal SettingTo set terminal parameters Shown belowParity None Stop bits Set the following parameters Bits per second 9600 Data bitsHyperTerminal Window Connect Dialog Box Powering on RouterStartup Process ConfigurationFundamentals Router Configuration Fundamentals of the Router Ethernet Serial synchronous/asynchronous Asynchronous E1/T1 Naming and Arranging InterfacesMaintaining the Router Boot Menu Boot MenuIntroduction Through XModem Options of Boot ROM operation menu includeUpgrading application program Send File dialog box Restoring the Extended Segment of Boot ROM Program Upgrading the entire Boot ROM programRestore the extended segment of Boot ROM program from Flash Upgrading the extendedIntroduction Router restarts after successful upgrading Press Enter to reboot the systemBuild up FTP remote upload/download environment Build up FTP local upload/download environmentSpecify FTP directory Add right levelStart FTP server Ftpquit Cover Power LED is Off TroubleshootingNothing is Displayed on the Terminal after Power-On Repeated Reboot Power-OnIllegible Characters Display onRUN LED Remains On After Startup, All LEDs Remain OnRUN LED Blinks Rapidly During Sartup RUN LED Blinks Slowly After StartupTroubleshooting Signal Direction DB-25 DB-9 Cable SpecificationsConsole Cable Console Cable PinoutsEthernet Cable AUX CableSignal Twisted Pair Signal Direction Signal Category Signal DirectionStraight-through Network Cable Pinouts Crossover Network Cable PinoutsDTE and DCE Mode Serial Interface Cable Synchronous and Asynchronous ModeTypical DTE and DCE EIA/TIA-232 Maximum Transmission Baud rate bps Distance mPinouts DB-50 Signal Signal Direction DB-25Describes the V.24 DTE cable pinouts 24 DTE Cable PinoutsAssembly and Pinouts DCE Cable illustrates the V.24 DCE cable assemblyDescribes the V.24 DCE cable pinouts 24 DCE Cable PinoutsDescribes the V.35 DTE cable pinouts DB-50 Signal Signal Direction35 DTE Cable Pinouts Describes V.35 DCE cable pinouts 35 DCE cable Pinouts DCE Cable illustrates the V.35 DCE cable assemblyE1 Cable Dumb Terminal AdapterT1 Cable Describes T1 cable pinoutsPin 4 and pin 5 are the receiving end Isdn cablesProduct Contact Us Warranty, you can obtain an RMA number online at PasswordNumber, URL or e-mail address from the list below Support telephone numbers posted on the 3Com web site atUS and Canada Telephone Technical Support and Repair Latin America Telephone Technical Support and RepairAppendix a Obtaining Support for Your Product