Teka IR 635, IQ 644, IZ 622 Locking the hob sensors, Switching the Appliance OFF, Safety Function

Page 15

selected. The corresponding decimal point (11) must be lit.

2 Use sensor (4) to decrease the power to level 0. The hotplate will automatically switch off.

To turn it off quickly: Whatever the power level, the hotplate is turned off

immediately if you touch the and sensors (2/4) simultaneously.

If all the cooking areas are positioned at 0, all the display points will flash.

When a hotplate is switched off, an H will appear on the corresponding power dis- play if the surface of the glass in the corresponding cooking area reaches a temperature at which there is a risk of bur- ning. When the temperature drops, the display will go out (if the hob is disconnec- ted), or a 0 is displayed if the hob is still on.

SWITCHING THE APPLIANCE OFF

The appliance may be switched off at any time by touching the general on / off sen- sor (1). When in standby mode, an H is displayed on any hot areas. None of the other hotplate displays will light up.

After use, disconnect the device using the control; do not rely on the cookware detector.

Locking the hob sensors

SAFETY FUNCTION

(models ...635, ...645, ...735 AB and ...622)

The safety function can be enabled after the hob is connected. To do so, touch sen-

sor (1) to enable the touch control. Immediately, touch the sensor (4) and hold it down for five seconds. An L (for 'Locked') will appear on the displays. The

GB

touch control will be switched off after a few seconds. If the cooking area is hot, an L and an H will appear alternately on the corresponding display.

This operation needs to be done within 10 seconds, with no sensor other than those indicated being touched during that time, or the locking will not be carried out.

The electronic control will remain locked until the user unlocks it, even after the con- trol is disconnected using the sensor

(1)or when restarting after there has been a power cut.

Unlocking in order to cook

To unlock the control and use it, touch sen-

sor (1) to enable the touch control. Immediately touch the two sensors on the right at the same time. The L vanishes from the displays and a 0 appears with the lower point flashing, or an H if the corres- ponding hotplate is hot, and the hob will be ready to use for cooking. When you switch off the control using the on/off sensor

(1)the safety function will be re-enabled and will reappear the next time the touch control is enabled.

Cancelling the safety function

The safety function can be permanently

disabled by pressing sensor for 5 seconds immediately after enabling the touch control. This should be done within 10 seconds after enabling the touch con- trol using the on/off sensor (1), and the safety function will be cancelled. If this is not done properly, the touch control will remain locked and will switch off after 20 seconds.

After cancelling the safety function, when the control is re-enabled using the on/off sensor (1), the hob will be ready to be

17

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Induction Hobs Contents / Inhalt / Table des Matières Anmerkungen zum Kochgeschirr für Ihr Induktionskochfeld Introduction / Einführung / PrésentationModèle IR 622 / IT Model IR 622 / IT Model IT 645 / IRModell IR 622 / IT Modèle IT 645 / IRModel IR 735 AB Model IT 635 / IRDE Modell IT 635 / IR FR Modèle IT 635 / IRNormal conditions Model IR Model IQInside circle on the cooking area Modell IR Represents the minimum base diameterModell IQ Tions normales dutilisation Model IQ Modèle IQSafety instructions GB Guide to Using the Instructions BookletPositioning the hob InstallationInstallation with Cutlery DRA- WER or Lower Cabinet Installation with FAN Oven Under the HOBModel Installing the AIR Nozzle Models …604Fastening the hob Fitting holesConnecting the electricity Model Dimensions and characteristicsGB Technical Information Technical detailsUse and Maintenance Before starting for First timeControl Panel Elements see figs , 6 Switching the Appliance on Switching the Hotplates onSwitching the Hotplate OFF Switching the Appliance OFF Safety FunctionLocking the hob sensors Timing a hotplate Timer functionFunction for keeping a pan hot Models …622 Lock Function modelsSwitching the Countdown Timer on Clock as a countdown timerDisconnecting the clock Switching off quicklyControl Panel Elements see fig Disconnecting the Countdown TimerSwitching OFF Quickly Touch control user instruc Tions models ...640It is selected, i.e. that the correspon Before using a hotplate, first check thatTo turn a hotplate up to full power Switching the Hotplates OFFStop Function Function for keeping a pan hot Models …622 Adjusting the Programmed Time Detecting pans Induction hotplates Power supplied according to Power level selectedSwitching HEAT-UP on Touch control user instruc Tions for all the modelsExample Power function Concentrated power Except ...604 modelModifying the Power Level During HEAT-UP Switching HEAT-UP Function OFFMaximum Operating Time Disconnection for safety PurposesOverheating safety feature Safety Against Covering SensorsGB Table HEAT-UP Cooking FeatureSuggestions and recommendations Power surgesHeavy soiling Cleaning and careRecommended Cleaning Products Light soilingWhen the glass’s colour changes Using the scraperTo decrease the hotplate gets less hot Fault Possible cause Possible solutionGB If something doesn’t work Induction zones are not heating upMessage ER 21 on the control and subsequent disconnection Hotplate switches off and error message E2 is displayedMessage U400 and the beeping signal Areas are activated at high power levelsWhen cooking at a level below 9, there will be fluctuations Message E3 in the controlIf an induction element goes off and the message E2 appears
Top Page Image Contents