Teka IR 735, IR 635, IQ 644 manual Positioning the hob, Installation with FAN Oven Under the HOB

Page 9

Installation

INSTALLATION AND SETUP SHOULD BE CARRIED OUT BY AN AUTHORISED TECHNICIAN IN LINE WITH CURRENT INSTALLATION STANDARDS.

Positioning the hob

To install these models, an opening with the dimensions shown in figure 2 will be cut into the unit’s worktop.

The minimum distance between the surfa- ce supporting the cooking pans and the lower part of the kitchen unit or the hood located above the hob should be 650 mm. If the hood’s installation instructions recommend that the gap is greater than this, you should follow this advice.

The unit where the hob and oven will be located will be suitably fixed.

INSTALLATION WITH CUTLERY DRA- WER OR LOWER CABINET

In mixed induction - vitroceramic hobs, if you would like to have a cabinet or a cutlery drawer under the hob, it is neces- sary to put a separation board in between the two. The board should be situated 20

mmbelow the underside of the hob, lea- ving a free space of at least 20 mm until the end of the cabinet (figure 1).

This prevents accidental contact with the hot surface of the casing of the heating elements under the apparatus (figure 1).

In induction hobs, there should be a mini- mum distance of 5 cm between the drawer and the opening to the fan (a separating board is not necessary).

Please do not store objects that can obstruct the hob fans or possibly flammable materials in the drawer.

GB

Minimum distance	fig. 1
to wall

Minimum ventilation distances

DRAWER

OVEN

Mixed hobs:

DRAWER

INSTALLATION WITH FAN OVEN UNDER THE HOB

The oven should be installed according to the corresponding manual.

11

Image 9

Contents Induction Hobs Contents / Inhalt / Table des Matières Anmerkungen zum Kochgeschirr für Ihr Induktionskochfeld Introduction / Einführung / PrésentationModell IR 622 / IT Model IR 622 / IT Model IT 645 / IRModèle IT 645 / IR Modèle IR 622 / ITDE Modell IT 635 / IR Model IT 635 / IRFR Modèle IT 635 / IR Model IR 735 AB Inside circle on the cooking area Model IR Model IQ Modell IR Represents the minimum base diameter Normal conditionsModell IQ Tions normales dutilisation Model IQ Modèle IQSafety instructions GB Guide to Using the Instructions BookletInstallation with Cutlery DRA- WER or Lower Cabinet InstallationInstallation with FAN Oven Under the HOB Positioning the hobFastening the hob Installing the AIR Nozzle Models …604Fitting holes ModelConnecting the electricity GB Technical Information Dimensions and characteristicsTechnical details ModelUse and Maintenance Before starting for First timeControl Panel Elements see figs , 6 Switching the Appliance on Switching the Hotplates onSwitching the Hotplate OFF Switching the Appliance OFF Safety FunctionLocking the hob sensors Function for keeping a pan hot Models …622 Timer functionLock Function models Timing a hotplateDisconnecting the clock Clock as a countdown timerSwitching off quickly Switching the Countdown Timer onSwitching OFF Quickly Disconnecting the Countdown TimerTouch control user instruc Tions models ...640 Control Panel Elements see figTo turn a hotplate up to full power Before using a hotplate, first check thatSwitching the Hotplates OFF It is selected, i.e. that the corresponStop Function Function for keeping a pan hot Models …622 Adjusting the Programmed Time Switching HEAT-UP on Power supplied according to Power level selectedTouch control user instruc Tions for all the models Detecting pans Induction hotplatesModifying the Power Level During HEAT-UP Power function Concentrated power Except ...604 modelSwitching HEAT-UP Function OFF ExampleOverheating safety feature Disconnection for safety PurposesSafety Against Covering Sensors Maximum Operating TimeGB Table HEAT-UP Cooking FeatureSuggestions and recommendations Power surgesRecommended Cleaning Products Cleaning and careLight soiling Heavy soilingWhen the glass’s colour changes Using the scraperGB If something doesn’t work Fault Possible cause Possible solutionInduction zones are not heating up To decrease the hotplate gets less hotMessage U400 and the beeping signal Hotplate switches off and error message E2 is displayedAreas are activated at high power levels Message ER 21 on the control and subsequent disconnectionWhen cooking at a level below 9, there will be fluctuations Message E3 in the controlIf an induction element goes off and the message E2 appears