Teka IQ 644, IR 635, IZ 622 Hotplate switches off and error message E2 is displayed, Induction

Page 31

GB

Fault		Possible cause	Possible solution
Sounds similar to "whistles" are heard when two or more			induction
areas are activated at high power levels.
		An energy coupling occurs	It is not a defect; try changing
		in the different induction	the power levels chosen.
		areas.

A hotplate switches off and error message E2 is displayed

		The glass has overheated.	Remove the pan and let the
			glass cool down.

An L will appear in the indicators and the control will			not
work (except models …604)
		The control is blocked.	Follow the instructions
			manual to unblock the
			control.

MODELS ...635, ...645 AND ...735 AB:

Message U400 and the beeping signal

		Surges in the electricity	Contact the Technical
		supply	Service

Message ER 21 on the control and subsequent disconnection

		If, whilst cooking, the tempe-	Leave the hob to cool
		rature of the control electro-	down for a few minutes. If
		nics gets too high, it will dis-	the problem persists, check
		connect to avoid damage.	that installation was perfor-
		Overheating problems only	med in compliance with the
		occur while cooking under	instructions in this manual.
		extreme conditions of use
		(cooking for a long time at
		full power).

Message ER 03 on the control and the beeping signal. Control disconnection

	There is an object or liquid	Remove the object or liquid
	covering up the touch	that is covering the touch
	control.	control.

MODEL ...622:

When connecting the hob to the power for the first time or after a power fai- lure, the H of residual heat will turn on in the radiant plates, even though the glass is cold.

	A power failure occurs when	It is not a defect. The H indica-
	the H were on.	tors will disappear after some
		time has passed.

33

Image 31

Contents Induction Hobs Contents / Inhalt / Table des Matières Anmerkungen zum Kochgeschirr für Ihr Induktionskochfeld Introduction / Einführung / PrésentationModèle IR 622 / IT Model IR 622 / IT Model IT 645 / IRModell IR 622 / IT Modèle IT 645 / IRModel IR 735 AB Model IT 635 / IRDE Modell IT 635 / IR FR Modèle IT 635 / IRNormal conditions Model IR Model IQInside circle on the cooking area Modell IR Represents the minimum base diameterModell IQ Tions normales dutilisation Model IQ Modèle IQSafety instructions GB Guide to Using the Instructions BookletPositioning the hob InstallationInstallation with Cutlery DRA- WER or Lower Cabinet Installation with FAN Oven Under the HOBModel Installing the AIR Nozzle Models …604Fastening the hob Fitting holesConnecting the electricity Model Dimensions and characteristicsGB Technical Information Technical detailsBefore starting for First time Use and MaintenanceControl Panel Elements see figs , 6 Switching the Hotplates on Switching the Appliance onSwitching the Hotplate OFF Safety Function Switching the Appliance OFFLocking the hob sensors Timing a hotplate Timer functionFunction for keeping a pan hot Models …622 Lock Function modelsSwitching the Countdown Timer on Clock as a countdown timerDisconnecting the clock Switching off quicklyControl Panel Elements see fig Disconnecting the Countdown TimerSwitching OFF Quickly Touch control user instruc Tions models ...640It is selected, i.e. that the correspon Before using a hotplate, first check thatTo turn a hotplate up to full power Switching the Hotplates OFFStop Function Function for keeping a pan hot Models …622 Adjusting the Programmed Time Detecting pans Induction hotplates Power supplied according to Power level selectedSwitching HEAT-UP on Touch control user instruc Tions for all the modelsExample Power function Concentrated power Except ...604 modelModifying the Power Level During HEAT-UP Switching HEAT-UP Function OFFMaximum Operating Time Disconnection for safety PurposesOverheating safety feature Safety Against Covering SensorsGB Table HEAT-UP Cooking FeatureSuggestions and recommendations Power surgesHeavy soiling Cleaning and careRecommended Cleaning Products Light soilingWhen the glass’s colour changes Using the scraperTo decrease the hotplate gets less hot Fault Possible cause Possible solutionGB If something doesn’t work Induction zones are not heating upMessage ER 21 on the control and subsequent disconnection Hotplate switches off and error message E2 is displayedMessage U400 and the beeping signal Areas are activated at high power levelsMessage E3 in the control When cooking at a level below 9, there will be fluctuationsIf an induction element goes off and the message E2 appears