Lenoxx Electronics Optima 3 FS operation manual Damper Locations, Damper Adjustment

Page 12

INSTALLATION

Optima 3 INS (Only) – Install damper rod knob as ex- plained on page 11.

Left

Surround

Panel

For less air, slide damper knob to the right (or) for more air, slide knob to the left.

More Air

Less Air

Damper

Knob

Adjustment Procedure: The damper knob should be positioned in the center of the oblong slot for the aver- age installation (see illustration above). If more or less air is needed, then adjust in ¼" increments until opti- mum combustion air flow is achieved (see Damper Ad- justment Guidelines on page 26).

Damper Locations

See ‘Opening Side Panels’, page 33 for instructions on opening the side panels for models Optima 2 FS & Op- tima 3 FS. See ‘Installing Surround Assembly’ for in- structions on side surround panel access for model Op- tima 3 INS.

Optima 2 FS - The damper control handle is located on the right-hand side panel.

Optima 3 FS - The damper control handle is located on the left-hand side panel.

Optima 3 INS - The damper control handle is located on the left surround panel.

Damper Adjustment

It is very important to preset your damper prior to burn- ing your pellet stove.

Damper - Air Control Handle – Freestanding Units

Damper is factory set to a gap as specified below. Follow Damper Adjustment Guidelines on page 26.

1 5/8" – Optima 3 FS

To adjust,

use a

1 1/2" – Optima 2 FS

3/32" allen

wrench

 

to loosen set collar.

Adjustment Procedure: Loosen setscrew on set collar (see above picture), then adjust in ¼" increments until optimum combustion air flow is achieved. For less air push in and for more air pull out. After adjustment, posi- tion set collar against side panel and tighten setscrew.

PAGE 12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Installation and Operation Manual Freestanding Insert Pellet Fired StovesImportant Warnings Table of Contents Planning Your Installation Installation / Maintenance StandardsSelecting a Location Smoke DetectorsFloor Protection Optima 2 FS Top View of Model Optima 2 FSFloor Protection / Hearth Extension Using Clearances Minimum Clearances to CombustiblesOptima 3 FS Fireplace Warning Label Provided in accessory package Masonry and Factory Built FireplacesMinimum Fireplace Firebox Size Top ViewModels Optima 2 FS and Optima 3 FS Installation Installation Check ListRemoving Appliance from Pallet Installation Damper Adjustment Damper LocationsDamper Air Control Handle Freestanding Units Thermostat Installation Model Optima 3 FSModel Optima 3 INS Model Optima 2 FSInstalltion Venting RequirementsVent Termination Site Built Residential Home Chimney Height RequirementsManufactured Mobile Home Chimney Height Requirements Determining Size of Pipe to Install Installation ChartSample Installation Chart Pipe Selection ChartInstalling Your Freestanding Pellet Stove Standard Horizontal Vent InstallationGasket Optima 3 FS Corner Through the Wall Optima 2 FS Corner Through the WallPreferred Installation Vertical Vent Through Roof Exterior Vertical VentVertical Vent Into a Masonry Flue Existing Class a Chimney USA & Canada Direct Connection / Positive Flue Connection Direct Connection Not allowed in CanadaInstalling Optima 3 INS Vent Termination When Liner is UsedCare and Operation Control Board OperationStart-up Sequence of Events Combustion Voltage Trim Steps Fuel Delivery RateLighting Procedure Without Igniter Manual OperationAutomatic Operation Turning OFF Your Pellet StoveDamper Adjustment Guideline Automatic Safety FeaturesPower Outage Damper Operation All modelsFuel UltraGrateRoutine Maintenance Routine CleaningUltraGrate Burn Grate for All Models Use tool to grab scraper rod Removing Photoeye Filter for Cleaning Photoeye Access Inside HopperClean Photoeye Lens Clean-Out Tee Remove Filter and Wipe CleanASH CLEAN-OUT Ports Door Rope Gasket All Models Door Rope GasketChecking Door Seal Creosote Removal All Models Window WashSmall Area Paint TOUCH-UP Rear Stove Compartment All ModelsMotor Lubrication Back View Side ViewFuel delivery and burn times will vary depending On size and type of fuel used. Estimated heat inputBased on fuel value of 8400 BTU per lb 23 5/8 TOP ViewComponent Definitions Wiring Diagram Troubleshooting Qualified Technicians Only Troubleshooting Qualified Technicians Only Troubleshooting Qualified Technicians Only Replacement Parts List Electrical Parts Item # Description Stove ModelFirebox Parts Item # Description Stove Model Auger System Components Item # Description Stove ModelMisc Item # Description Stove Model Replacement Parts Diagrams Replacement Parts Diagrams Replacement Parts Diagrams Replacement Parts Diagrams Optional Accessories Diagrams Optional Accessories Item # Model Description Stove ModelInstallation Tips Simple Operating Instructions Label SAFETY/LISTING Label Model Optima 2 FS SAFETY/LISTING Label Model Optima 3 FS and Optima 3 INS Service and Maintenance LOG Ownership RecordsWest Taft Avenue Orange, CA

Optima 3 FS specifications

Lenoxx Electronics has established itself as a reputable brand in the audio equipment industry, and their Optima 3 FS model is a perfect illustration of their commitment to quality and innovation. Designed for both casual listeners and audiophiles alike, the Optima 3 FS combines advanced technology with user-friendly features, making it a compelling choice for anyone looking to enhance their audio experience.

One of the standout features of the Optima 3 FS is its outstanding sound reproduction capabilities. The speakers are engineered with high-quality drivers that deliver clear and balanced audio across a wide frequency range. Whether you’re listening to music, watching movies, or playing video games, the Optima 3 FS promises an immersive auditory experience that captures the essence of sound.

The model also boasts Bluetooth connectivity, allowing users to pair their smartphones and other devices effortlessly. This wireless feature provides convenience, enabling you to play music from your playlists or streaming services without the hassle of tangled cords. Additionally, the Optima 3 FS is equipped with USB and AUX inputs, ensuring compatibility with various audio devices.

Another significant characteristic of the Optima 3 FS is its compact and stylish design. The sleek finish and modern aesthetics make it an attractive addition to any home décor. Its compact size doesn’t compromise sound quality, making it perfect for smaller spaces where traditional large speakers might not fit.

The user interface is designed to be intuitive, featuring easy-to-use buttons and a clear display that allows for seamless navigation through functions and settings. Furthermore, the Optima 3 FS incorporates a remote control, providing added convenience to adjust volume, skip tracks, or change modes from a distance.

In terms of energy efficiency, the Optima 3 FS is designed to consume less power without sacrificing performance, making it an environmentally friendly choice. This model is also built with durability in mind, featuring robust components that ensure long-lasting use.

In summary, the Lenoxx Electronics Optima 3 FS stands out with its exceptional sound quality, versatile connectivity options, stylish design, and user-friendly features. It caters to a broad audience, from casual listeners to sound enthusiasts, making it a noteworthy addition to the realm of home audio solutions.
Top Page Image Contents