Lenoxx Electronics Optima 3 FS Masonry and Factory Built Fireplaces, Top View, Side View

Page 8

PLANNING YOUR INSTALLATION

MASONRY AND FACTORY BUILT FIREPLACES

The model Optima 3 INS is approved for installation into a solid fuel burning fireplace, either a masonry fireplace (built to UBC 37 or ULC S628 standards) or an approved factory-built / zero clearance fireplace (built to UL 127 or ULC S610 standards). See pages 20 and 21 for additional information on venting.

Minimum Fireplace Firebox Size

 

 

 

Height

 

20 1/8” / 512 mm

 

 

 

Width @ Front

 

32” / 814 mm

 

 

 

(extends back 1 ½”)

 

 

 

 

 

Width @ back

 

24 5/8” / 626mm

 

 

 

Depth

 

17 ¾” / 452 mm

 

 

 

 

 

 

 

 

 

Clean-out

24 5/8"

 

 

 

 

 

 

 

 

 

Tee

 

 

 

 

 

 

 

17 3/4"

 

 

 

 

 

Recommended

clear-

 

 

ance

zone

from the

 

 

front

of the

appliance

 

 

to combustibles

is 4

 

 

feet minimum.

 

32"

CAUTION: The fireplace in which the Optima 3 INS is to be installed must be thoroughly cleaned if it has been used to burn wood or synthetic logs. Have the chimney and all inside sur- faces of the fireplace brushed and vacuumed so that no soot, embers, or loose combustion deposits can be drawn into the heat circulation blower and blown into the living area. If any por- tion of the chimney system shows signs of structural or me- chanical weaknesses, such as: cracks, leaky joints, corroded or warped surfaces, the faulty portion must be repaired or replaced prior to installing this appliance.

IMPORTANT: When installing the Optima 3 INS into a factory built fireplace or heatform, the air flow within and around the fire- place shall not be altered by the installation of the insert (i.e. DO NOT BLOCK louvers or cooling air inlet or outlet ports, circulating air chambers in a steel fireplace liner or metal heat circulator). The factory built firebox must accept the insert without modification other than removing bolted or screwed together pieces such as smoke shelf / deflectors, ash lips, screen or door tracks and damper assemblies. Any fireplace component, which is removed, must be retained so they can be reinstalled to restore the fireplace to its original operating condition. The removal of any part must not alter the integrity of the outer shell of the pre-engineered fire- place cabinet in any way. A Warning Label (provided with appli- ance) must be installed in the fireplace firebox so that it shall be visible upon removal of the fireplace insert (see Fireplace Warning Label, below). Use RTV high Temperature Silicone as an adhe- sive to affix the warning label.

Fireplace Warning Label

(provided in accessory package)

THIS FIREPLACE HAS BEEN ALTERED TO ACCOMMO- DATE A FIREPLACE INSERT AND SHOULD BE IN- SPECTED BY A QUALIFIED PERSON PRIOR TO RE- USE AS A CONVENTIONAL FIREPLACE.

PAGE 8

HEARTH / FLOOR PROTECTION - Optima 3 INS The area directly in front of the Optima 3 INS must be protected by a noncombustible material or a fireplace hearth or hearth extension as fol- lows:

Combustible flooring must be protected by non-combustible material in Canada and 10 millimeter (3 / 8 inches) millboard or equivalent non-combustible in U.S. extending beneath the heater and to the front as indicated or to the nearest permitted combustible material. See page 6 for requirements when using alternate material as hearth extension.

The protected area must extend 6” to the front of the face of the Optima 3 INS.

MINIMUM CLEARANCES TO COMBUSTIBLES

 

inches / millimeters

A - Insert to side wall

6”

/ 153 mm

B - Insert to side trim

1”

/ 26 mm

C - Hearth extension

6”

/ 153 mm

D - Insert to mantel

18”

/ 458 mm

E - Insert to top trim

1”

/ 26 mm

 

Top View

 

Side Wall

 

Trim

Side View

Trim

Mantel

D

E

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Installation and Operation Manual Freestanding Insert Pellet Fired StovesImportant Warnings Table of Contents Planning Your Installation Installation / Maintenance StandardsSelecting a Location Smoke DetectorsFloor Protection Optima 2 FS Top View of Model Optima 2 FSFloor Protection / Hearth Extension Using Optima 3 FS ClearancesMinimum Clearances to Combustibles Fireplace Warning Label Provided in accessory package Masonry and Factory Built FireplacesMinimum Fireplace Firebox Size Top ViewModels Optima 2 FS and Optima 3 FS Removing Appliance from Pallet InstallationInstallation Check List Installation Damper Air Control Handle Freestanding Units Damper AdjustmentDamper Locations Thermostat Installation Model Optima 3 FSModel Optima 3 INS Model Optima 2 FSInstalltion Venting RequirementsManufactured Mobile Home Chimney Height Requirements Vent TerminationSite Built Residential Home Chimney Height Requirements Determining Size of Pipe to Install Installation ChartSample Installation Chart Pipe Selection ChartGasket Installing Your Freestanding Pellet StoveStandard Horizontal Vent Installation Optima 3 FS Corner Through the Wall Optima 2 FS Corner Through the WallVertical Vent Into a Masonry Flue Existing Class a Chimney Preferred Installation Vertical Vent Through RoofExterior Vertical Vent USA & Canada Direct Connection / Positive Flue Connection Direct Connection Not allowed in CanadaInstalling Optima 3 INS Vent Termination When Liner is UsedCare and Operation Control Board OperationStart-up Sequence of Events Combustion Voltage Trim Steps Fuel Delivery RateLighting Procedure Without Igniter Manual OperationAutomatic Operation Turning OFF Your Pellet StoveDamper Adjustment Guideline Automatic Safety FeaturesPower Outage Damper Operation All modelsFuel UltraGrateUltraGrate Burn Grate for All Models Routine MaintenanceRoutine Cleaning Use tool to grab scraper rod Removing Photoeye Filter for Cleaning Photoeye Access Inside HopperASH CLEAN-OUT Ports Clean Photoeye Lens Clean-Out TeeRemove Filter and Wipe Clean Door Rope Gasket All Models Door Rope GasketChecking Door Seal Creosote Removal All Models Window WashMotor Lubrication Small Area Paint TOUCH-UPRear Stove Compartment All Models Back View Side ViewBased on fuel value of 8400 BTU per lb Fuel delivery and burn times will vary dependingOn size and type of fuel used. Estimated heat input 23 5/8 TOP ViewComponent Definitions Wiring Diagram Troubleshooting Qualified Technicians Only Troubleshooting Qualified Technicians Only Troubleshooting Qualified Technicians Only Replacement Parts List Electrical Parts Item # Description Stove ModelMisc Item # Description Stove Model Firebox Parts Item # Description Stove ModelAuger System Components Item # Description Stove Model Replacement Parts Diagrams Replacement Parts Diagrams Replacement Parts Diagrams Replacement Parts Diagrams Optional Accessories Diagrams Optional Accessories Item # Model Description Stove ModelInstallation Tips Simple Operating Instructions Label SAFETY/LISTING Label Model Optima 2 FS SAFETY/LISTING Label Model Optima 3 FS and Optima 3 INS Service and Maintenance LOG Ownership RecordsWest Taft Avenue Orange, CA

Optima 3 FS specifications

Lenoxx Electronics has established itself as a reputable brand in the audio equipment industry, and their Optima 3 FS model is a perfect illustration of their commitment to quality and innovation. Designed for both casual listeners and audiophiles alike, the Optima 3 FS combines advanced technology with user-friendly features, making it a compelling choice for anyone looking to enhance their audio experience.

One of the standout features of the Optima 3 FS is its outstanding sound reproduction capabilities. The speakers are engineered with high-quality drivers that deliver clear and balanced audio across a wide frequency range. Whether you’re listening to music, watching movies, or playing video games, the Optima 3 FS promises an immersive auditory experience that captures the essence of sound.

The model also boasts Bluetooth connectivity, allowing users to pair their smartphones and other devices effortlessly. This wireless feature provides convenience, enabling you to play music from your playlists or streaming services without the hassle of tangled cords. Additionally, the Optima 3 FS is equipped with USB and AUX inputs, ensuring compatibility with various audio devices.

Another significant characteristic of the Optima 3 FS is its compact and stylish design. The sleek finish and modern aesthetics make it an attractive addition to any home décor. Its compact size doesn’t compromise sound quality, making it perfect for smaller spaces where traditional large speakers might not fit.

The user interface is designed to be intuitive, featuring easy-to-use buttons and a clear display that allows for seamless navigation through functions and settings. Furthermore, the Optima 3 FS incorporates a remote control, providing added convenience to adjust volume, skip tracks, or change modes from a distance.

In terms of energy efficiency, the Optima 3 FS is designed to consume less power without sacrificing performance, making it an environmentally friendly choice. This model is also built with durability in mind, featuring robust components that ensure long-lasting use.

In summary, the Lenoxx Electronics Optima 3 FS stands out with its exceptional sound quality, versatile connectivity options, stylish design, and user-friendly features. It caters to a broad audience, from casual listeners to sound enthusiasts, making it a noteworthy addition to the realm of home audio solutions.
Top Page Image Contents