Lenoxx Electronics Optima 3 FS operation manual Exterior Vertical Vent

Page 19

INSTALLATION

Standard Vertical Installation Configurations Models: Optima 2 FS and Optima 3 FS

These freestanding models may be connected to an existing flue or by installing listed type “PL” vent pipe. If a liner is run all the way to the top of the existing chim- ney, the existing flue should be sealed with a steel plate. Start a vertical run with a Tee at the back of the stove. Other options are illustrated below. Note: See page 15 for Vent Termination Requirements

Exterior Vertical Vent

Wall Straps Required Every 4 ft. Minimum

Preferred Installation – Vertical Vent Through the

Roof

This venting configuration allows for the best stove performance. The vertical pipe promotes natural draft and with the chimney inside the dwelling, the flue gases stay warm, thus rising at a consistent rate.

Listed Rain Cap

Flashing

3”

Min.

Clean-Out

Tee

 

Interior Vertical Vent into an

Vertical Vent Into A Masonry Flue

Existing Class A Chimney

Optional Com-

Existing

Chimney

plete Liner and

Pipe

Listed Termina-

 

tion Cap

Pipe Increaser

 

Optional Clean-Out

 

Access Door

 

3”

Min.

Extend Pipe to the Top if Exist- ing Chimney is

Corroded or Damaged

♦USA & Canada – Requires an approved noncombustible hearth or floor protector, 3/8” / (10 mm) millboard or equivalent (k = .84, r = 1.19) to extend 6” / 150 mm to the front of the glass door.

PAGE 19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Freestanding Insert Pellet Fired Stoves Installation and Operation ManualImportant Warnings Table of Contents Smoke Detectors Planning Your InstallationInstallation / Maintenance Standards Selecting a LocationTop View of Model Optima 2 FS Floor Protection Optima 2 FSFloor Protection / Hearth Extension Using Minimum Clearances to Combustibles ClearancesOptima 3 FS Top View Fireplace Warning Label Provided in accessory packageMasonry and Factory Built Fireplaces Minimum Fireplace Firebox SizeModels Optima 2 FS and Optima 3 FS Installation Check List InstallationRemoving Appliance from Pallet Installation Damper Locations Damper AdjustmentDamper Air Control Handle Freestanding Units Model Optima 2 FS Thermostat InstallationModel Optima 3 FS Model Optima 3 INSVenting Requirements InstalltionSite Built Residential Home Chimney Height Requirements Vent TerminationManufactured Mobile Home Chimney Height Requirements Pipe Selection Chart Determining Size of Pipe to InstallInstallation Chart Sample Installation ChartStandard Horizontal Vent Installation Installing Your Freestanding Pellet StoveGasket Optima 2 FS Corner Through the Wall Optima 3 FS Corner Through the WallExterior Vertical Vent Preferred Installation Vertical Vent Through RoofVertical Vent Into a Masonry Flue Existing Class a Chimney Direct Connection Not allowed in Canada USA & Canada Direct Connection / Positive Flue ConnectionVent Termination When Liner is Used Installing Optima 3 INSControl Board Operation Care and OperationStart-up Sequence of Events Fuel Delivery Rate Combustion Voltage Trim StepsTurning OFF Your Pellet Stove Lighting Procedure Without IgniterManual Operation Automatic OperationDamper Operation All models Damper Adjustment GuidelineAutomatic Safety Features Power OutageUltraGrate FuelRoutine Cleaning Routine MaintenanceUltraGrate Burn Grate for All Models Use tool to grab scraper rod Photoeye Access Inside Hopper Removing Photoeye Filter for CleaningRemove Filter and Wipe Clean Clean Photoeye Lens Clean-Out TeeASH CLEAN-OUT Ports Window Wash Door Rope Gasket All ModelsDoor Rope Gasket Checking Door Seal Creosote Removal All ModelsRear Stove Compartment All Models Small Area Paint TOUCH-UPMotor Lubrication Side View Back ViewOn size and type of fuel used. Estimated heat input Fuel delivery and burn times will vary dependingBased on fuel value of 8400 BTU per lb TOP View 23 5/8Component Definitions Wiring Diagram Troubleshooting Qualified Technicians Only Troubleshooting Qualified Technicians Only Troubleshooting Qualified Technicians Only Electrical Parts Item # Description Stove Model Replacement Parts ListAuger System Components Item # Description Stove Model Firebox Parts Item # Description Stove ModelMisc Item # Description Stove Model Replacement Parts Diagrams Replacement Parts Diagrams Replacement Parts Diagrams Replacement Parts Diagrams Optional Accessories Item # Model Description Stove Model Optional Accessories DiagramsInstallation Tips Simple Operating Instructions Label SAFETY/LISTING Label Model Optima 2 FS SAFETY/LISTING Label Model Optima 3 FS and Optima 3 INS Ownership Records Service and Maintenance LOGWest Taft Avenue Orange, CA

Optima 3 FS specifications

Lenoxx Electronics has established itself as a reputable brand in the audio equipment industry, and their Optima 3 FS model is a perfect illustration of their commitment to quality and innovation. Designed for both casual listeners and audiophiles alike, the Optima 3 FS combines advanced technology with user-friendly features, making it a compelling choice for anyone looking to enhance their audio experience.

One of the standout features of the Optima 3 FS is its outstanding sound reproduction capabilities. The speakers are engineered with high-quality drivers that deliver clear and balanced audio across a wide frequency range. Whether you’re listening to music, watching movies, or playing video games, the Optima 3 FS promises an immersive auditory experience that captures the essence of sound.

The model also boasts Bluetooth connectivity, allowing users to pair their smartphones and other devices effortlessly. This wireless feature provides convenience, enabling you to play music from your playlists or streaming services without the hassle of tangled cords. Additionally, the Optima 3 FS is equipped with USB and AUX inputs, ensuring compatibility with various audio devices.

Another significant characteristic of the Optima 3 FS is its compact and stylish design. The sleek finish and modern aesthetics make it an attractive addition to any home décor. Its compact size doesn’t compromise sound quality, making it perfect for smaller spaces where traditional large speakers might not fit.

The user interface is designed to be intuitive, featuring easy-to-use buttons and a clear display that allows for seamless navigation through functions and settings. Furthermore, the Optima 3 FS incorporates a remote control, providing added convenience to adjust volume, skip tracks, or change modes from a distance.

In terms of energy efficiency, the Optima 3 FS is designed to consume less power without sacrificing performance, making it an environmentally friendly choice. This model is also built with durability in mind, featuring robust components that ensure long-lasting use.

In summary, the Lenoxx Electronics Optima 3 FS stands out with its exceptional sound quality, versatile connectivity options, stylish design, and user-friendly features. It caters to a broad audience, from casual listeners to sound enthusiasts, making it a noteworthy addition to the realm of home audio solutions.
Top Page Image Contents