Lenoxx Electronics operation manual Models Optima 2 FS and Optima 3 FS

Page 9

PLANNING YOUR INSTALLATION

MANUFACTURED (MOBILE) HOME INSTALLATION Freestanding Models – Optima 2 FS and Optima 3 FS In addition to the standard installation instructions, the following instructions may be required by local, state or federal building codes:

Stove must be permanently bolted to the floor.

An outside air inlet must be provided for combustion and be unrestricted while unit is in use. Use a galva- nized or stainless steel pipe for the duct (the outside air inlet on the stove is 2" diameter).

Stove must be permanently electrically grounded to the steel chassis of the home. The location selected for ground attachment to the stove must be dedicated for this purpose.

See pages 14 through 19 for additional information on venting requirements.

Do not install appliance in a sleeping room.

The structural integrity of the manufactured home floor, walls, ceiling and roof must be maintained.

NOTE: The grounding of this product, at installation, must comply with NFPA-70 standards, CSA C22.1 in Canada, as well as any local codes.

MANUFACTURED (MOBILE) HOME EXHAUST VENT PIPE INSTALLATION GUIDELINES

Use only listed type “PL” pellet vent pipe. Pipe should extend at least 3 feet above the part of the roof through which it passes. The top of the pipe should be at least 2 feet above the highest required elevation of any part of the manufactured (mobile) home within 10 feet of the pipe.

If the exhaust vent exits the manufactured (mobile) home at a location other than the roof, and exits at a point 7 feet or less above the ground level on which the manufactured (mobile) home is positioned. A guard or method of enclosing the pipe shall be provided at the point of exit for a height of up to 7 feet. The openings, if any, in this guard shall not allow a 3/4” rod to pass through. A 1/2” rod could pass through but should not be able to touch the pipe when inserted through the opening a distance of 4 inches.

Models – Optima 2 FS and Optima 3 FS

 

Bolt

 

 

 

 

 

Floor Protector

Floor

 

 

 

 

Chassis

Ground to Steel Chassis

PAGE 9

Image 9
Contents Freestanding Insert Pellet Fired Stoves Installation and Operation ManualImportant Warnings Table of Contents Installation / Maintenance Standards Planning Your InstallationSelecting a Location Smoke DetectorsTop View of Model Optima 2 FS Floor Protection Optima 2 FSFloor Protection / Hearth Extension Using Clearances Minimum Clearances to CombustiblesOptima 3 FS Masonry and Factory Built Fireplaces Fireplace Warning Label Provided in accessory packageMinimum Fireplace Firebox Size Top ViewModels Optima 2 FS and Optima 3 FS Installation Installation Check ListRemoving Appliance from Pallet Installation Damper Adjustment Damper LocationsDamper Air Control Handle Freestanding Units Model Optima 3 FS Thermostat InstallationModel Optima 3 INS Model Optima 2 FSVenting Requirements InstalltionVent Termination Site Built Residential Home Chimney Height RequirementsManufactured Mobile Home Chimney Height Requirements Installation Chart Determining Size of Pipe to InstallSample Installation Chart Pipe Selection ChartInstalling Your Freestanding Pellet Stove Standard Horizontal Vent InstallationGasket Optima 2 FS Corner Through the Wall Optima 3 FS Corner Through the WallPreferred Installation Vertical Vent Through Roof Exterior Vertical VentVertical Vent Into a Masonry Flue Existing Class a Chimney Direct Connection Not allowed in Canada USA & Canada Direct Connection / Positive Flue ConnectionVent Termination When Liner is Used Installing Optima 3 INSControl Board Operation Care and OperationStart-up Sequence of Events Fuel Delivery Rate Combustion Voltage Trim StepsManual Operation Lighting Procedure Without IgniterAutomatic Operation Turning OFF Your Pellet StoveAutomatic Safety Features Damper Adjustment GuidelinePower Outage Damper Operation All modelsUltraGrate FuelRoutine Maintenance Routine CleaningUltraGrate Burn Grate for All Models Use tool to grab scraper rod Photoeye Access Inside Hopper Removing Photoeye Filter for CleaningClean Photoeye Lens Clean-Out Tee Remove Filter and Wipe CleanASH CLEAN-OUT Ports Door Rope Gasket Door Rope Gasket All ModelsChecking Door Seal Creosote Removal All Models Window WashSmall Area Paint TOUCH-UP Rear Stove Compartment All ModelsMotor Lubrication Side View Back ViewFuel delivery and burn times will vary depending On size and type of fuel used. Estimated heat inputBased on fuel value of 8400 BTU per lb TOP View 23 5/8Component Definitions Wiring Diagram Troubleshooting Qualified Technicians Only Troubleshooting Qualified Technicians Only Troubleshooting Qualified Technicians Only Electrical Parts Item # Description Stove Model Replacement Parts ListFirebox Parts Item # Description Stove Model Auger System Components Item # Description Stove ModelMisc Item # Description Stove Model Replacement Parts Diagrams Replacement Parts Diagrams Replacement Parts Diagrams Replacement Parts Diagrams Optional Accessories Item # Model Description Stove Model Optional Accessories DiagramsInstallation Tips Simple Operating Instructions Label SAFETY/LISTING Label Model Optima 2 FS SAFETY/LISTING Label Model Optima 3 FS and Optima 3 INS Ownership Records Service and Maintenance LOGWest Taft Avenue Orange, CA

Optima 3 FS specifications

Lenoxx Electronics has established itself as a reputable brand in the audio equipment industry, and their Optima 3 FS model is a perfect illustration of their commitment to quality and innovation. Designed for both casual listeners and audiophiles alike, the Optima 3 FS combines advanced technology with user-friendly features, making it a compelling choice for anyone looking to enhance their audio experience.

One of the standout features of the Optima 3 FS is its outstanding sound reproduction capabilities. The speakers are engineered with high-quality drivers that deliver clear and balanced audio across a wide frequency range. Whether you’re listening to music, watching movies, or playing video games, the Optima 3 FS promises an immersive auditory experience that captures the essence of sound.

The model also boasts Bluetooth connectivity, allowing users to pair their smartphones and other devices effortlessly. This wireless feature provides convenience, enabling you to play music from your playlists or streaming services without the hassle of tangled cords. Additionally, the Optima 3 FS is equipped with USB and AUX inputs, ensuring compatibility with various audio devices.

Another significant characteristic of the Optima 3 FS is its compact and stylish design. The sleek finish and modern aesthetics make it an attractive addition to any home décor. Its compact size doesn’t compromise sound quality, making it perfect for smaller spaces where traditional large speakers might not fit.

The user interface is designed to be intuitive, featuring easy-to-use buttons and a clear display that allows for seamless navigation through functions and settings. Furthermore, the Optima 3 FS incorporates a remote control, providing added convenience to adjust volume, skip tracks, or change modes from a distance.

In terms of energy efficiency, the Optima 3 FS is designed to consume less power without sacrificing performance, making it an environmentally friendly choice. This model is also built with durability in mind, featuring robust components that ensure long-lasting use.

In summary, the Lenoxx Electronics Optima 3 FS stands out with its exceptional sound quality, versatile connectivity options, stylish design, and user-friendly features. It caters to a broad audience, from casual listeners to sound enthusiasts, making it a noteworthy addition to the realm of home audio solutions.