Raypak 751 manual Horizontal Thru-wall Venting System Category IV Installation

Page 36

 

Model

Venting Category

Certified Venting

Vent Size (inches)

Maximum Vent

 

 

Material

Length (feet)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

UL 1738 Certified

 

55 Subtract 10 ft per

 

 

 

 

Venting Material e.g.

 

 

 

ADB-751 w/CHX

IV

8

elbow, Max. 3

 

 

AL29-4C Stainless

 

 

 

 

 

elbows

 

 

 

 

Steel PVC*, CPVC*

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

UL 1738 Certified

 

55 Subtract 10 ft per

 

 

 

 

Venting Material e.g.

 

 

 

ADB-1001 w/CHX

IV

10

elbow, Max. 3

 

 

AL29-4C Stainless

 

 

 

 

 

elbows

 

 

 

 

Steel PVC*, CPVC*

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

UL 1738 Certified

 

55 Subtract 10 ft per

 

 

 

 

Venting Material e.g.

 

 

 

ADB-1501 w/CHX

IV

12

elbow, Max. 3

 

 

AL29-4C Stainless

 

 

 

 

 

elbows

 

 

 

 

Steel PVC*, CPVC*

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

*Contact the manufacturer for details.

 

 

 

 

 

 

 

 

 

 

 

 

 

Table P: Horizontal Thru-wall Venting with Add-on Condensing Heat Exchanger

 

 

 

 

 

 

 

 

 

Horizontal Thru-wall Venting System (Category IV) Installation

This installation utilize the boiler mounted blower to vent the combustion products to the outdoors. Combustion air is taken from inside the room and the vent is installed horizontally through the wall to the out- doors. Adequate combustion and ventilation air must be supplied to the boiler room in accordance with the National Fuel Gas Code or, in Canada, the latest edi- tion of CSA B149 Installation Code for Gas Burning Appliances and Equipment.

UL 1738 Certified Venting Material (e.g. AL29-4C) MUST be used. The vent must be installed to prevent flue gas leakage. Care must be taken during assembly to ensure that all joints are sealed properly and are air- tight.

For certain installations, i.e. pool, heat pump, domes- tic hot water supply with pre-heat tank, PVC or CPVC may be used. Contact manufacturer for details.

To prevent condensate accumulation in the vent, it is required to install the horizontal portion of vent with a slight upward slope of not more than 1/4" per foot of horizontal run and an approved condensate trap must be installed per applicable codes, so the condensation in the vent pipe drains back to the boiler.

WARNING: For common vent installations contact factory.

WARNING: No substitutions of flue pipe or vent cap material are allowed. Such substitutions would jeopardize the safety and health of inhabitants.

The Stainless Steel non-restrictive direct vent cap must be furnished by the boiler manufacturer in accordance with its listing.

36

Image 36
Contents Advanced Design Boiler Page Contents Pay Attention to These Terms Before Installation Installations at ElevationProduct Receipt Model IdentificationComponent Locations Component LocationsGeneral Safety Time/Temperature Relationships in ScaldsInstallation Installation CodesIndoor Installations Equipment BaseOutdoor Installations Combustion and Ventilation AirIndoor Units Direct VentInstallations1 Canadian Installations2 Installations Canadian InstallationsConventional Combustion Air Supply Low Temperature System Temperature & Pressure GaugeWater Piping GeneralHydronic Heating Single Boiler Primary/Secondary Piping Dual Boiler Piping Domestic HOT Water Piping Single Boiler Domestic Hot Water with One Storage Tank Page Pool Heating Automatic Chlorinators and Chemical FeedersWinterizing Your Heater Pool and Spa Water ChemistrySingle Boiler Pool Application GAS Supply Connections Double Boiler Pool ApplicationGas Supply Connection Gas Supply PressureElectrical Power Connections Field Wiring Connections Electrical Connections Domestic Hot WaterVenting Connections General Definition of Appliance CategoriesVent Terminal Location Venting Installation Tips Venting ConfigurationsADB-1501 Natural Draft Vertical Venting System Installation Natural Draft Vertical Vent TerminationADB-1501 Horizontal Thru-wall Direct Vent Termination Horizontal Thru-Wall Direct Venting/Combustion Air CategoryÁDB-1501 Vertical Direct Venting/Combustion Air Category Vertical Direct Venting System Installation Vertical Direct Vent TerminationContact the manufacturer for details Horizontal Thru-wall Venting System Category IV Installation PVC, ABS Page Galvanized ADB-751 Venting Material e.g Subtract 10 ft per Condensate Drain Condensate Trap AlignmentCentral Point Wiring CPW ControlsCPW Board Pump Turn-off Delay Freeze Protection FeatureBlower Fan Pre-purge Blower Fan Post-purgeDiagnostics Board Light Color IndicationWiring Diagram Figure L-2Flow Switch High Limit Manual ResetHigh Limit Auto Reset Ignition Control ModuleHigh and Low Gas Pressure Switches Manual Reset PRE-START-UPLow Water Cut Off Optional Fill the SystemPre-Start-up Check Blower T Fitting DetailADB Initial START-UP Tools NeededPreparation for Start-up Page Main Burner Adjustment Safety InspectionPost START-UP Check Follow-upMaintenance Suggested Minimum Maintenance ScheduleOperation Operating InstructionsConnecting the Condensing Heat Exchanger CHX Cleaning Boiler Heating SurfacesDaily MonthlyVent Switch Adjustment Connecting Add-on Condensing Heat Exchanger to ADBAppendix Inside Combustion Air ContaminationEmissions Settings and Test Information Bluff Head Body Burner Warranty

751 specifications

The Raypak 751 is a high-efficiency, gas-powered pool and spa heater renowned for its advanced technology and durability. Designed with innovative features, the Raypak 751 prioritizes user convenience and energy efficiency, making it an excellent choice for pool owners seeking reliable heating solutions.

One of the standout features of the Raypak 751 is its robust heat exchanger, built from the finest materials to ensure long-lasting performance. This model utilizes a copper heat exchanger which is highly conductive, allowing for rapid heating of water and maintenance of consistent temperatures. Its design also minimizes scale buildup, extending the longevity of the heater.

The Raypak 751 is equipped with advanced digital controls that make it user-friendly. The intuitive interface allows for precise temperature settings and monitoring, ensuring optimal performance. Additionally, the heater features a temperature display that provides real-time updates, giving users peace of mind when adjusting their pool's environment.

Energy efficiency is a hallmark of the Raypak 751, thanks to its low NOx burner technology. This feature meets stringent environmental regulations while also lowering operational costs. By optimizing fuel usage, the heater not only contributes to reducing greenhouse gas emissions but also provides a more economical heating option for pool and spa owners.

The rugged construction of the Raypak 751 is another characteristic that sets it apart. Its heavy-duty cabinet is designed to withstand the elements, ensuring reliable operation in various weather conditions. The heater is available in multiple configurations, including both natural gas and propane options, allowing for flexible installation depending on the user's needs.

Furthermore, the Raypak 751 incorporates safety features, such as an integrated pressure switch that prevents operation when water flow is insufficient. This protects both the heater and associated plumbing from damage due to overheating or dry firing.

In summary, the Raypak 751 combines cutting-edge technology with user-centric features to deliver a superior pool heating experience. Its high-efficiency performance, durable construction, and advanced safety features make it a top choice for anyone looking to enhance their pool or spa. Whether for residential or commercial applications, the Raypak 751 ensures warmth and comfort, enriching the overall swimming experience.