Raypak 1000, 500, 750 installation instructions

Page 41

•Vertical Vent (Category IV) with Add-on Condensing Heat Exchanger Installation

These installations utilize the boiler mounted blower to vent the combustion products to the outdoors. Combustion air is taken from inside the room and the vent is installed vertically through the roof to the outdoors. Adequate combustion and ventilation air must be supplied to the boiler room in accordance with the National Fuel Gas Code or, in Canada, the latest edition of CAN/CGA-B149.1 AND .2. Installation Code for Gas Burning Appliances and Equipment.

UL 17-38 Certified Venting Material (e.g. AL29-4C) MUST be used. The vent must be installed to prevent the flue gas leakage. Care must be taken during assembly to insure that all joints are sealed properly and are airtight.

For certain installations, i.e. pool, heat-pump domestic hot water with pre-heat tank, PVC or CPVC may be used. Contact Manufacturer for details.

To prevent the condensation accumulation in the vent, it is required to install the horizontal portion of vent with a slight upward slope of not more than 1/4" per foot of horizontal run and an approved condensate trap must be installed per applicable codes.

WARNING:

No substitutions of flue pipe or vent cap material are allowed. Such substitutions would jeopardize the safety and health of inhabitants.

The Stainless Steel non-restricted direct vent cap must be furnished by the boiler manufacturer in accordance with AGA/CGA requirements.

41

Page 40 Page 42
Image 41
Page 40 Page 42
Contents For Your Safety What to do if YOU Smell GAS For Your SafetyPage Table of Contents Product Receipt Section a Before Installing the BoilerRatings and Certification ModelidentificationAdvanced Design Boiler Component Locations Figure A-1Equipment Base Section B Boiler InstallationInstallation Codes Figure B-1 Outdoor Installation Minimum Clearances Direct Combustion AIR Section C Combustion and Ventilation AIRPage Temperature & Pressure Gauge LOW Temperature SystemSection D Water Piping General Reliefvalve PipingPump Selection Section E Hydronic Heating PipingPiping Heating Boilers Pressure Drop in Feet of Head Feedwater RegulatorAIR-SEPARATION/EXPANSION Tank THREE-WAY ValvesDUAL-BOILER PRIMARY/SECONDARY Piping Single Boiler PRIMARY/SECONDARY Piping with CHXDual Boiler -PRIMARY/SECONDARY Piping with CHX Figure E-3bSingle Boiler Domestic HOT Water with ONE Storage Tank Section F Domestic HOT Water PipingFigure F-1c Winterizingyour Heater Section G Pool HeatingAutomatic Chlorinators and Chemical Feeders Single Boiler Pool Application with CHX Spawater ChemistrySingle Boiler Pool Application Double Boiler Pool Application Figure G-3aGAS Supply Pressure Section H GAS Supply ConnectionsGAS Supply Connection Venting of Diaphragm GAS Components Regulator Pressure SettingsGAS Pressure Regulator Check the Power Source Section I Electrical Power ConnectionsCheck Power Source Surge ProtectionMaking the Electrical Connections Field Wiring ConnectionElectrical Connections Domestic HOT Water General Section J Venting ConnectionsPage Support of Vent Stack Venting Configurations Figure J-1 Natural Draft Vertical Vent Termination Page Heat Exchanger Category Section J-2Page Category Section J-3Page Vertical Direct Venting/Combustion Air Category Section J-4Vertical Direct Venting System Installation Figure J-5 Page Figure J-6 Section J-6Horizontal Thru-wall Venting System Category IV Installation Figure J-7 Page Figure J-8 Page Outdoor Installation withAdd-On Condensing Heat Exchanger Condensate Trap Alignment Section K Condensate DrainCPW Board Central Point Wiring CPWSection L Controls Figure L-1 CPW Board Pump Turn-off Delay Manual High Limit Red Figure L-2 Wiring DiagramManual Reset High Limit Flow Switch High Limit Manual ResetFlow Switch High Limit Auto Reset Auto Reset High LimitPressure Control Device ACU-TRACK GAS Pressure SwitchLOW Water CUT OFF Optional TIME/TEMPERATURE Relationships in Scalds Section M General Safety PrecautionsSection N PRE-START-UP Component and Pressure TAP Locations Figure O-1Preparation for START-UP Do not Turn on GAS AT this Time Section O ADB Initial START-UPTools Needed START-UP Page CO2 Section P Post START-UP CheckEmissions Guidelines To Turn OFF GAS to Appliance Section Q OperationOperating Instructions Suggested Minimum Maintenance Schedule Section R MaintenanceCleaning Boiler Heating Surfaces Vent Switch Adjustment Section S Connecting Condensing Heat Exchanger CHXInsidecombustionaircontamination Appendix aPage Page Page Page Page Pressure Settings START-UP SettingsLitho in U. S. a
Related manuals
Manual 8 pages 63.38 Kb Manual 8 pages 12.19 Kb

1000, 750, 500 specifications

Raypak is a renowned name in the heating industry, particularly known for its high-quality pool and spa heaters. Among their extensive product line, the Raypak 850, 500, 300, 400, and 700 models stand out for their reliability, efficiency, and cutting-edge technologies. Each model is designed to cater to different needs and applications while maintaining Raypak’s commitment to performance.

The Raypak 850 is designed for larger commercial pools or residential setups requiring high output. With a powerful heat exchanger made from copper and bronze, it ensures superior heat transfer and longevity. Its digital control system provides precise temperature regulation, enhancing user experience. Moreover, it features a durable construction with weather-resistant materials, ensuring lasting performance in various environments.

The Raypak 500 model offers a balance between efficiency and compactness. It features eco-friendly technology that reduces energy consumption without sacrificing performance. The integrated thermostat allows users to maintain consistent water temperatures, making it ideal for residential pools. This model is well-regarded for its user-friendly digital display, simplifying operation and monitoring.

For those needing a more moderate capacity, the Raypak 300 is an efficient choice. It combines robust engineering with an easy-to-use interface. Its advanced ignition system improves reliability while minimizing energy waste. The Raypak 300’s compact design allows for easy installation in various spaces, making it an excellent option for smaller pools.

The Raypak 400 heats water quickly and efficiently, making it suitable for both residential pools and spas. It features a high-capacity heating system that ensures optimal performance. With a clear LED display, users can easily monitor their settings, while the integrated diagnostics provide real-time feedback for maintenance and troubleshooting.

Lastly, the Raypak 700 model is known for its versatility and robust performance. It is equipped with advanced safety features, including a high limit switch and water flow detection mechanism, to ensure safe operation. The model's energy-efficient design enhances its eco-friendliness, making it a popular choice among environmentally conscious users.

Collectively, these Raypak models exemplify superior engineering, performance, and user-friendliness. Their innovative features ensure that they meet the varied demands of pool owners while providing reliable heating solutions for leisure and relaxation. Whether for commercial or residential use, the Raypak 850, 500, 300, 400, and 700 offer unmatched quality and efficiency.
Top Page Image Contents