Samsung SDM-160P, SDM-160MP, SDM-090P manual Basic Method to use, Initial operation

Page 19

Digital Multiplexer

Chapter 4. Basic Method to use

Initial operation

1. Turn on power switch.

A 4-division screen appears on the monitor if firstly operating after purchase. In this case, the channel without inputting appears in the blue background on the screen and a video loss occurs.

(The current operation status is memorized when the power turns off after completing the initial setting and thus the unit operates in the operation status when the power turns off if turning power on.)

2. Setup a recording channel.

Set the channel without inputting to “off” in the “DUTY SET” of “1.REC OUT SET” on the program menu.

3.Change it to a desiring indication mode.

-Indication of FULL screen: The selected channel is indicated on monitor in the form of FULL channel.

-Indication of division screen: The division screen is indicated on monitor if pressing the multi- screen button. Resetting channel is available for the division screen if user wants.

-Indication of automatic sequential conversion: The full screen is automatically converted if pressing the sequence button.

-Indication of stop screen: A desired channel can be seen in a form of stop screen using the freezing button and camera selection button.

-Indication of live/P.B: The current camera signal may be monitored or the recorded screen may be reproduced for a view using the live/P.B button.

-Indication of TRIPLEX screen: The current camera signal and the recorded screen may be seen on the same monitor using the TRIPLEX button.

-Indication of PIP screen: The PIP (picture in picture) screen may be seen using the PIP button.

-Indication of expansion screen: The full screen may be expanded up to 4 times for view using the zoom and move button.

-Indication of record check screen: The recorded output screen or the output screen of VCR may be seen using the REC CHECK button.

When desiring to see in the live screen/replay screen

The “live/P.B” select button determines the live screen/replay screen mode. The LED turns on in the live mode and it turns off in the tape replay mode.

If pressing this button, the indication mode is changed to the replay mode for the live mode and to the live mode for the replay mode.

➢The “LIVE/P.B” button does not operate in the following cases:

-During zoom operation

-In setting of program mode

-In displaying ALARM/LOSS LIST on screen

When desiring to see in the TRIPLEX screen

The “TRIPLEX” button sets the TRIPLEX screen mode. In this case the LED turns on and the previous TRIPLEX division mode is set.

➢The “TRIPLEX” button does not operate in the following cases:

-During zoom operation

-In setting of program mode

-In displaying ALARM/LOSS LIST on screen

ENGLISH

4-1

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Digital Multiplexer Important Safeguards Iii Contents Appendix B Checking Points in Trouble Introduction IntroductionName of parts and Function Move → Rear panel Physical & Environmental Preparing for the InstallationPrecautions when Installing Digital Multiplexer Unpacking Connecting to normal VCR and Monitor Connecting to Other DevicesConnecting to S-VHS VCR and S-VHS Monitor Connecting to Time Lapse VCR Connecting to Alarm Sensor Ascii Remote Control by connecting to PCSpot OUT Control Remote Control using SSC-1000RS-485Monitor OUT Control @ Spot OUT ControlInitial operation When desiring to see in the live screen/replay screenWhen desiring to see in the Triplex screen Basic Method to useWhen desiring to see in the division screen When desiring to see in the Full screenWhen desiring to see automatic sequential conversion screen When desiring to see in the zoom screen When desiring to see the stop screenFull Mode 2TIMES Zoom Times Zoom When desiring to see in the record screen When desiring to see in the PIP screenWhen desiring to see output of VCR as it is Duty SET Reservation OFF Setting of Program MenuRecord setting of each camera REC OUT SET Type TLVREC Reservation Start Time REC Duty SET CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9END Time PB Display ALL Spot OUT Cvbs PIP Size Setting of display modeSequence Loss Detect Loss Info Alarm Info Motion Info ALLSequence Alarm S/W TimeCH15 on Setting of title by channelIjklmnopqrstuvwxyz Title SETDATE/TIME SET Display Type Setting of motion Setting of alarmMotion OUT OFF ↔ on List Update OFF ↔ onXxxxx Sensitivity OFF ↔ LOW ↔ Medium ↔ HighBaud Rate System settingPassword Change Password Check OFF Alarm Buzzer Loss Buzzer Summer Time+++++++++++++++++ + - - - - + Password Change Password Check NEW Password ConfirmTime Lapse record mode Normal record modeRecording REC Duty Weight value REC Duty recordAlarm weight value record Reservation recordAlarm signal standard Alarm occurrence conditionsAlarm release Alarm recordOperation in video loss Alarm/Loss list referenceOperation in motion detection Image input Appendix a SpecificationsOutside Drawing Appendix B Checking points in trouble When record is not done
Related manuals
Manual 69 pages 50.93 Kb
Top Page Image Contents