Samsung SDM-160P, SDM-160MP, SDM-090P manual Recording, Normal record mode, Time Lapse record mode

Page 34

Digital Multiplexer

Chapter 6. Recording

1. Normal record mode

When setting the “REC TYPE” of the setup menu “1.REC OUT SET” to “NOR”.

(1)Frame record

-When setting the “REC TYPE” of the setup menu “1.REC OUT SET” to FRAME.

-The image signal entered from the maximum 16 cameras is output in Frame and recorded on the VCR.

-The recorded output records the only channel that the “REC DUTY” of the “1.REC OUT SET” is set to more than 1.

1/30sec(NTSC), 1/25(PAL)

(2)Field record

-When setting the “REC TYPE” of the setup menu “1.REC OUT SET” to “FIELD”.

-The image signal entered from the maximum 16 cameras is output in Field and recorded on the VCR.

-The recorded output records the only channel that the “REC DUTY” of the “1.REC OUT SET” is set to more than 1.

1/60sec(NTSC), 1/50(PAL)

2.TIME LAPSE record mode

-When setting the “REC TYPE” of the setup menu “1.REC OUT SET” to “TLV”.

-The image signal entered from the maximum 16 cameras is recorded on the VCR in response to the trigger signal of VCR.

-The recorded output records the only channel that the “REC DUTY” of the “1.REC OUT SET” is set to more than 1.

-The trigger out of VCR and the VTR terminal this unit must be connected.

-“NO TRIGGER” character is displayed on screen while operating the field record operation of the normal mode if the trigger signal is not received for 10 seconds.

Trigger output from TIME LAPSE VCR

6-1

Image 34

Contents Digital Multiplexer Important Safeguards Iii Contents Appendix B Checking Points in Trouble Introduction IntroductionName of parts and Function Move → Rear panel Preparing for the Installation Physical & EnvironmentalPrecautions when Installing Digital Multiplexer Unpacking Connecting to normal VCR and Monitor Connecting to Other DevicesConnecting to S-VHS VCR and S-VHS Monitor Connecting to Time Lapse VCR Connecting to Alarm Sensor Remote Control by connecting to PC Ascii@ Spot OUT Control Remote Control using SSC-1000RS-485Monitor OUT Control Spot OUT ControlBasic Method to use When desiring to see in the live screen/replay screenWhen desiring to see in the Triplex screen Initial operationWhen desiring to see in the Full screen When desiring to see in the division screenWhen desiring to see automatic sequential conversion screen When desiring to see in the zoom screen When desiring to see the stop screenFull Mode 2TIMES Zoom Times Zoom When desiring to see in the record screen When desiring to see in the PIP screenWhen desiring to see output of VCR as it is REC OUT SET Type TLV Setting of Program MenuRecord setting of each camera Duty SET Reservation OFFREC Reservation Start Time REC Duty SET CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9END Time ALL Setting of display modeSequence Loss Detect Loss Info Alarm Info Motion Info PB Display ALL Spot OUT Cvbs PIP SizeAlarm S/W Time SequenceSetting of title by channel CH15 onIjklmnopqrstuvwxyz Title SETDATE/TIME SET Display Type Setting of alarm Setting of motionSensitivity OFF ↔ LOW ↔ Medium ↔ High List Update OFF ↔ onXxxxx Motion OUT OFF ↔ onPassword Check OFF Alarm Buzzer Loss Buzzer Summer Time System settingPassword Change Baud RatePassword Change Password Check NEW Password Confirm +++++++++++++++++ + - - - - +Time Lapse record mode Normal record modeRecording Reservation record Weight value REC Duty recordAlarm weight value record REC DutyAlarm record Alarm occurrence conditionsAlarm release Alarm signal standardOperation in video loss Alarm/Loss list referenceOperation in motion detection Appendix a Specifications Image inputOutside Drawing When record is not done Appendix B Checking points in trouble

Related manuals

Manual 69 pages 50.93 Kb