Samsung SDM-160P REC Duty SET CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9, REC Reservation Start Time

Page 25

Digital Multiplexer

-The following screen is displayed if pressing the “ENTER” button with the blinking position placed at the “DUTY SET ….”.

[REC DUTY SET]

CH1

: 1

CH2

: 1

CH3

: 1

CH4

: 1

CH5

: 1

CH6

: 1

CH7

: 1

CH8

: 1

CH9

: 1

CH10 : 1

CH11: 1

CH12 : 1

CH13: 1

CH14 : 1

CH15: 1

CH16 : 1

ENGLISH

The blinking indication moves if pressing “”, “” button.

The setting value is changed if pressing “ ”, “” button:OFF,1~5.

The relevant channel is not recorded if the setting value is “OFF”.

The changed setting value is stored if pressing the “SET” button. You can return to the main menu.

-The following screen is displayed if pressing the “ENTER” button where the blinking position is “ON…” at the “RESERVATION ….”.

[REC RESERVATION]

START TIME

00:01[HH:MM]

END TIME

23:59[HH:MM]

CH1 : 1

CH2 : 1

CH3 : 1

CH4 : 1

CH5 : 1

CH6 : 1

CH7 : 1

CH8 : 1

CH9 : 1

CH10: 1

CH11: 1

CH12: 1

CH13: 1

CH14: 1

CH15: 1

CH16: 1

Useful menu when desiring to record only specific channels at a specific time.

Record the channels set from the start time to the end time.

The blinking indication moves if pressing “”, “” button.

The setting value is changed if pressing “”, “” button. Start time, end time HH : 00 ~ 23

Start time, end time MM : 00 ~ 59

CH1 ~ CH16 : OFF ↔ 1 ↔ 2 ↔ 3 ↔ 4 ↔ 5 ↔ OFF

Channels set to “OFF” does not perform when carrying out reservation record.

The changed setting value is stored if pressing the “SET” button. You can return to the “REC OUT SET” menu.

5-2

Image 25
Contents Digital Multiplexer Important Safeguards Iii Contents Appendix B Checking Points in Trouble Introduction IntroductionName of parts and Function Move → Rear panel Physical & Environmental Preparing for the InstallationPrecautions when Installing Digital Multiplexer Unpacking Connecting to normal VCR and Monitor Connecting to Other DevicesConnecting to S-VHS VCR and S-VHS Monitor Connecting to Time Lapse VCR Connecting to Alarm Sensor Ascii Remote Control by connecting to PCMonitor OUT Control Remote Control using SSC-1000RS-485@ Spot OUT Control Spot OUT ControlWhen desiring to see in the Triplex screen When desiring to see in the live screen/replay screenBasic Method to use Initial operationWhen desiring to see in the division screen When desiring to see in the Full screenWhen desiring to see automatic sequential conversion screen When desiring to see in the zoom screen When desiring to see the stop screenFull Mode 2TIMES Zoom Times Zoom When desiring to see in the record screen When desiring to see in the PIP screenWhen desiring to see output of VCR as it is Record setting of each camera Setting of Program MenuREC OUT SET Type TLV Duty SET Reservation OFFREC Reservation Start Time REC Duty SET CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9END Time Sequence Loss Detect Loss Info Alarm Info Motion Info Setting of display modeALL PB Display ALL Spot OUT Cvbs PIP SizeSequence Alarm S/W TimeCH15 on Setting of title by channelIjklmnopqrstuvwxyz Title SETDATE/TIME SET Display Type Setting of motion Setting of alarmXxxxx List Update OFF ↔ onSensitivity OFF ↔ LOW ↔ Medium ↔ High Motion OUT OFF ↔ onPassword Change System settingPassword Check OFF Alarm Buzzer Loss Buzzer Summer Time Baud Rate+++++++++++++++++ + - - - - + Password Change Password Check NEW Password ConfirmTime Lapse record mode Normal record modeRecording Alarm weight value record Weight value REC Duty recordReservation record REC DutyAlarm release Alarm occurrence conditionsAlarm record Alarm signal standardOperation in video loss Alarm/Loss list referenceOperation in motion detection Image input Appendix a SpecificationsOutside Drawing Appendix B Checking points in trouble When record is not done
Related manuals
Manual 69 pages 50.93 Kb