Samsung SDM-160MP, SDM-160P, SDM-090P manual Rear panel

Page 9

Digital Multiplexer

Rear panel

ENGLISH

F G H A IBE C DJ

A. CAMERA INPUT / LOOP THROUGH OUT

-Up to 16 camera signals can be input. When transmitting camera signals to external devices, OUT terminal can be used.

B.ALARM IN / ALARM OUT / VTI TERMINAL

-VTI: TRIGGER Output Connection terminal of VCR

-ALARM IN: Up to 16 ALARM Sensors can be connected. “G” indicates grounding terminal connected to ALARM Input, and should be connected to grounding terminal of sensors.

-ALARM OUT (HOT/COLD): When ALARM is activated, ACTIVE MAKE Signal is generated.

-ALARM RESET : Connected to RESET terminal of VCR, and when ALARM is deactivated, PULSE is generated.

-MOTIOM OUT(M/O) : When MOTION is activated, ACTIVE MAKE signal is generated.

C.VCR IN/OUT (BNC)

Indicates terminal for connecting to VCR Input/Output.

D. MONITOR OUT (BNC)

Indicates terminal for connecting to Monitor’s video Input terminal.

E. SPOT OUT (BNC)

Indicates terminal for connecting to Monitor’s video Input terminal.

F. VCR IN/OUT (4PIN MINI DIN)

Indicates terminal for connecting to VCR’s S-VHS Input/Output terminal.

✴SDM-160M/SDM-160MP:Not used.

G.MONITOR OUT (4PIN MINI DIN)

Indicates terminal for connecting to Monitor’s video S-VHS Input terminal.

✴ SDM-160M/SDM-160MP:Not used.

H.RS-232C

With RS-232C cable, Remote Control can be done.

I. RS-485

With RS-485 cable, Remote Control can be done.

J. ~AC IN

Connects to Power Cord.

1-4

Image 9

Contents Digital Multiplexer Important Safeguards Iii Contents Appendix B Checking Points in Trouble Introduction IntroductionName of parts and Function Move → Rear panel Physical & Environmental Preparing for the InstallationPrecautions when Installing Digital Multiplexer Unpacking Connecting to Other Devices Connecting to normal VCR and MonitorConnecting to S-VHS VCR and S-VHS Monitor Connecting to Time Lapse VCR Connecting to Alarm Sensor Ascii Remote Control by connecting to PCMonitor OUT Control Remote Control using SSC-1000RS-485@ Spot OUT Control Spot OUT ControlWhen desiring to see in the Triplex screen When desiring to see in the live screen/replay screenBasic Method to use Initial operationWhen desiring to see in the division screen When desiring to see in the Full screenWhen desiring to see automatic sequential conversion screen When desiring to see the stop screen When desiring to see in the zoom screenFull Mode 2TIMES Zoom Times Zoom When desiring to see in the PIP screen When desiring to see in the record screenWhen desiring to see output of VCR as it is Record setting of each camera Setting of Program MenuREC OUT SET Type TLV Duty SET Reservation OFFREC Duty SET CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 REC Reservation Start TimeEND Time Sequence Loss Detect Loss Info Alarm Info Motion Info Setting of display modeALL PB Display ALL Spot OUT Cvbs PIP SizeSequence Alarm S/W TimeCH15 on Setting of title by channelTitle SET IjklmnopqrstuvwxyzDATE/TIME SET Display Type Setting of motion Setting of alarmXxxxx List Update OFF ↔ onSensitivity OFF ↔ LOW ↔ Medium ↔ High Motion OUT OFF ↔ onPassword Change System settingPassword Check OFF Alarm Buzzer Loss Buzzer Summer Time Baud Rate+++++++++++++++++ + - - - - + Password Change Password Check NEW Password ConfirmNormal record mode Time Lapse record modeRecording Alarm weight value record Weight value REC Duty recordReservation record REC DutyAlarm release Alarm occurrence conditionsAlarm record Alarm signal standardAlarm/Loss list reference Operation in video lossOperation in motion detection Image input Appendix a SpecificationsOutside Drawing Appendix B Checking points in trouble When record is not done

Related manuals

Manual 69 pages 50.93 Kb