Samsung SDM-160MP Alarm occurrence conditions, Alarm release, Alarm record, Alarm signal standard

Page 36

Digital Multiplexer

Chapter 7. Occurrence and handling of alarm, loss, motion

1. Alarm occurrence conditions

The following events occur if alarm occurs since the sensor is connected to the alarm input terminal on the backside:

1)Warning sounds (if buzzer turns “ON”).

2)Alarm information (date and time when alarm occurs) is recorded on the alarm list.

3)“RESET” LED blinks.

4)The alarm output (HOT, COLD) signal is active for the alarm hold time.

5)The record times of the channel that alarm occurs increase.

6)Display character of “ALARM” or “A” appears (if the alarm information turns “ON”).

7)Alarm continues for the alarm hold time that is set in the program mode.

Alarm holds time: Time performing alarm operation after recognizing alarm.

2.Alarm release

The alarm status is released if pressing the “RESET” button when alarm occurs or the alarm holds time setting passes.

3. Alarm record

Perform the alarm weight value record in the chapter 6.

4. Alarm signal standard

You can view record output when alarm occurs during record.

For example, if record status have the following conditions:

Currently perform record in the TLV mode on the time lapse VCR.

Set the “REC TYPE” to “NOR” in the “5. ALARM SET” of the “program mode”.

The record output until release after the alarm occurs is as follows:

VCR TRIG

Record output operation

ALARM/MOTION OUT Output

ALARM RESET

Output

TRIG override

TLV operation

NOR operation

TLV

More than 150ms

Alarm occurrence

Alarm reset

7-1

Image 36
Contents Digital Multiplexer Important Safeguards Iii Contents Appendix B Checking Points in Trouble Introduction IntroductionName of parts and Function Move → Rear panel Preparing for the Installation Physical & EnvironmentalPrecautions when Installing Digital Multiplexer Unpacking Connecting to Other Devices Connecting to normal VCR and MonitorConnecting to S-VHS VCR and S-VHS Monitor Connecting to Time Lapse VCR Connecting to Alarm Sensor Remote Control by connecting to PC AsciiRemote Control using SSC-1000RS-485 Monitor OUT Control@ Spot OUT Control Spot OUT ControlWhen desiring to see in the live screen/replay screen When desiring to see in the Triplex screenBasic Method to use Initial operationWhen desiring to see in the Full screen When desiring to see in the division screenWhen desiring to see automatic sequential conversion screen When desiring to see the stop screen When desiring to see in the zoom screenFull Mode 2TIMES Zoom Times Zoom When desiring to see in the PIP screen When desiring to see in the record screenWhen desiring to see output of VCR as it is Setting of Program Menu Record setting of each cameraREC OUT SET Type TLV Duty SET Reservation OFFREC Duty SET CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 REC Reservation Start TimeEND Time Setting of display mode Sequence Loss Detect Loss Info Alarm Info Motion InfoALL PB Display ALL Spot OUT Cvbs PIP SizeAlarm S/W Time SequenceSetting of title by channel CH15 onTitle SET IjklmnopqrstuvwxyzDATE/TIME SET Display Type Setting of alarm Setting of motionList Update OFF ↔ on XxxxxSensitivity OFF ↔ LOW ↔ Medium ↔ High Motion OUT OFF ↔ onSystem setting Password ChangePassword Check OFF Alarm Buzzer Loss Buzzer Summer Time Baud RatePassword Change Password Check NEW Password Confirm +++++++++++++++++ + - - - - +Normal record mode Time Lapse record modeRecording Weight value REC Duty record Alarm weight value recordReservation record REC DutyAlarm occurrence conditions Alarm releaseAlarm record Alarm signal standardAlarm/Loss list reference Operation in video lossOperation in motion detection Appendix a Specifications Image inputOutside Drawing When record is not done Appendix B Checking points in trouble
Related manuals
Manual 69 pages 50.93 Kb