Samsung SNR-1162P/XET manual Installation Precautions, Checking Installation Environment

Page 11

installation

INSTALLATION PRECAUTIONS

-Make sure to turn the product off before installation.

-Avoid strong impact or vibration because it may damage the product.

-Do not install in a place exposed to strong electromagnetic ﬁ elds, or near a radio device such as a radio, TV etc.

-Keep the installation place clean when and after installing the product so that there is no dust.

-Install the product on an open, ﬂ at surface and maintain an appropriate temperature. In addition, keep the system at least 15 cm away from the wall.

-Take care not to allow a conductive object to fall into the vents.

-Install the system in a cool place out of direct sunlight and keep the devices and tools away from an aisle so as to prevent possible injury.

-If when using the system that generates smoke, it may cause a ﬁ re or an electric shock. In this case, turn the system off using the power switch and contact your system provider to request technical support.

-Carefully examine possible causes of faults such as damp ﬂ oor, power extension cable without ground, worn-out power cord, no safe ground, and so on.

CHECKING INSTALLATION ENVIRONMENT

Check installation environment for safe use of the system. This system can be installed on a ﬂ at table.

This system must be installed horizontally. Do not stand it vertically or diagonally.

The location of the main body and the power outlet is very important for proper operation of the system.

The system may not work properly in a place where the equipment is too close, or with poor ventilation due to lack of a ventilation system. And the system maintenance can be challenged in an environment where the system could harly be accessed.

To prevent trouble with the system and to prevent cases when the system is shutdown by operation environment, ventilate the air in the system installation place and ﬁ x the system cover ﬁ rmly. Since there are high-voltage parts inside the system, do not open the cover.

Use this system in the following operation environment where constant temperature and humidity is maintained.

-Operation temperature: 5°C to 40°C

-Operation humidity: 20% to 95% RH

-Ventilation: the front intake vents and the back exhaust vents should not blocked.

 INSTALLATION

English _11

Image 11

Contents Channel DVR Overview Product FeaturesImportant Safety Instructions Safety RegulationsBefore Start Continuous standard load 0.2mA Operating temperature -20C ~ +85CStandards Approvals Normal capacity 170mAhContents Communication Setup Camera SetupSchedule Setup Alarm Sensor SetupPackage Contents Used to eject a CD/DVD from the drive Shows HDD access operationsShows CD/DVD access operations Front View and Function DescriptionsBack View and Function Descriptions Checking Installation Environment InstallationInstallation Precautions Connecting Sensors and Alarms Connecting with Other DevicesShutting Down the System Getting startedStarting and Shutting Down the System Starting the SystemLogging Out Logging in and OUTLogging Live Screen Main Mode Buttons Surveillance Live Mode Screen Layout Surveillance modeCamera Information Panel Surveillance mode One channel screen layout Screen Information DisplayTo Set Screen Layout Setting Screen LayoutScreen Screen DisplayClick Camera Layout Presets Setting Camera LayoutDeleting a Layout Switching LayoutsPTZ Control Menu Controlling a Remote PTZ CameraNumber Conﬁrming Preset LocationStarting a Preset Registering LocationMoving to Center Screen Deleting a PresetStarting a Pattern Controlling the MouseControlling Audio Controlling ZOOM/AUDIOControlling Zoom Level Click OK and remove the USB device Current Time Display Status Display BARSearch Panel Layout ONE Channel SearchOne channel search One Channel Search Screen LayoutTo be searched in the search panel To Use Channel SearchOther Search Menus WindowSearch Mode Screen Layout Search modeSearch mode Search Panel Layout and Functions Overwritten Detail SearchSmaller motion Set Smart Search Area Smart SearchClick Detail Search Move to a time point that you want to searchMAP Search To Search with Detailed Time To Search using the Time BarText Search Search mode Event Search Search with DATE/TIME Select a backup drive and folder Backup SearchConfiguration Mode Screen Layout Conﬁ guration modeCamera Setup GRX-2000, CCR-20G PTZ Model Set up PTZ camera modelLG LPT-SD160S, LG MultiX Pelco D-ProtocolSetting Motion Detection Network Camera Setting is not applied to network cameras 3 are setPTZ Registering Presets Video Beep SettingLive Scanning Mode Schedule Setup Schedule SetupRecording schedule Other Buttons Deletes the selected day from the holiday list Holiday SettingSets the selected day as holiday HolidaySensor Setup Alarm Sensor Setup54 conﬁ guration mode Alarm SetupBasic Settings Communication SetupPTZ Port Setup TCP/IP SetupDVR Keyboard Setup Set up Ddns Dynamic DNS Mail Address SetupDdns Setup When authorization is requiredUser/Password Setup Screen Layout and Functions USER/PASSWORD SetupRegistering a New User User Authority SetupDeleting a Registered User Changing a PasswordRenaming a User Setting NTP Server System SetupBasic System Setup Shows the setting status of the HDD of the system UPS SetupSetting HDD Overwrite Option Drive Setting Data/BackupSetting Automatic Backup Channel Network Drive Setting Date/Time Information Display Event Alarm Setup66 conﬁ guration mode Text Input Device Basic Settings Text SetupSet up preset for the text input device linked with the DVR System Environment Settings for Issuing a ReceiptText Input Device Preset Setting Modifying a Registered Preset Text Input Device Event Trigger Settings Use Event Trigger Shell Mode Desk Top Setup Configuration SettingsSystem Setup Control Panel Disk Management Language SettingsLOG Viewer Custom Setup Mode Custom setup modeExternal monitor Rotation Mode Shows pictures in the selected screenLayout rotating the channels Custom setup mode Deleting a Registered DVR Server to ServerRegistering a DVR Server Modifying Registered DVR ServerConnecting a DVR Server Screen Layout and Functions Custom setup mode Searching for Recording of another DVR Data Backup Data Backup Backup Size of each data is 64MB Camera All Selects all the channels camerasSaving as AVI Video PrintingSaving Recording Screen Saving as BMP or JPG Still Picture Printing Recording Screen Search screen to be printed, click the Print Mode buttonLogout / Shutdown EndingProduct View AppendixTroubleshooting FAQ Check if the network settings have been changed Check if the PAN / Tilt type setting is correctExtension card driver is properly installed Set the DMZ setting of the sharerServer DisabledAccount with Admin authority, in the client Check if the client PC speaker is turned onPreamble Open Source License Report on the ProductYou may not copy, modify, sublicense, or What the Program doesNo Warranty END of Terms Conditions How to Apply These Terms to Your New ProgramsPreamble Appendix English Appendix Copyright C year name of author How to Apply These Terms to Your New LibrariesLoss of USE, DATA, or Profits or Business Interruption OpenSSL LicenseThis Software is Provided by Eric Young ‘‘AS IS’’ Product Specifications ~12 kbytes / frame CIF 480ips 352×288 / 704×288 / 704×576 CIF @ 352×240 ~3 kbytes / frameImage Size Half VGA ~6 kbytes / frame @ 704×240 Remote Display AccessibleSpecs Details Monitoring Environment 16ch Full Motion TransmissionPTZ RS-232 Audio Inputmono RCA 16 ports Main TV OutputVIDEOMain TV Spot Monitor OutputCorrect disposal of batteries in this product

Related manuals

Manual 110 pages 55.47 Kb