Fixing the installation plate
1. Disassemble the cover panel as described in page 38~39. |
2. Remove the Hanger plate from the indoor unit. |
(1) Unscrew 2 screws that fixes the Hanger plate to the indoor unit. |
(2) Push the hooks (on the bottom part of the indoor unit) up to release the installation plate from the hooks that holds it. |
(3) Pull the installation plate to release it completely from the indoor unit. |
Screw |
3. Determine the position of the pipe and drain hose hole as seen in the picture and drill the hole with an inner diameter |
of 65 mm so that it slants slightly downwards. |
Pipe hole (Ø65 mm) |
|
|
| Pipe hole (Ø65 mm) |
|
| |||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
07stIn llan atio
A
B
D | A |
C
B
D
C
|
|
|
|
|
|
| (Unit : mm) |
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
| Model | A | B | C |
| D |
|
| • Make sure to drill only one hole after choosing the |
|
| ||||||||||
|
|
| ||||||||||||||||||||||
|
|
| 12 | 36 | 120 | 81 |
| 36 |
|
|
| direction of the pipe. |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||
|
|
| 18/24 | 33 | 110 | 110 |
| 33 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
4. Fix the indoor unit. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
If you fix the indoor unit | on a | wall |
|
|
|
|
|
|
| Plastic |
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
| Anchor |
|
|
|
|
|
|
|
|
| ||||||||
(1) Fix the installation plate to the wall giving attention to the weight of the indoor unit. |
|
|
|
|
|
|
|
|
| Wall | ||||||||||||||
| < 20 mm |
|
| |||||||||||||||||||||
|
|
|
| • If you mount the plate to a concrete wall using plastic anchors, make sure that gaps |
|
|
|
|
| |||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||
|
|
|
| between the wall and the plate, created by projected anchor, is less than 20 mm |
|
|
|
|
|
|
|
|
|
|
| |||||||||
If you fix the indoor unit | on a | window frame |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
(1)Determine the positions of the wooden uprights to be attached to the window frame.
(2)Attach the wooden uprights to the window frame giving attention to the weight of the indoor unit.
(3)Attach the installation plate to the wooden upright using tapping screws.
If you fix the indoor unit on a gypsum board
(1)Use stud finder to find out locations of the studs.
(2)Fix the plate hanger on two studs.
• Search for other spots if there are less than two studs, or the distance between the studs are different from the plate hanger.
•Fix the installation plate without inclining to one side.
•Make sure that a wall can withstand the weight of the product. If you install the product in a place where it is not
strong enough to withstand the product weight, the unit could fall and cause injury.
Assembling the hanger screw
Use 2 screws to fix the indoor unit with hanger plate as shown in the picture.
Screw
English-37
9/1/2014 5:11:08 PM