Samsung AP0AS0ANXSG Refrigerant piping work, Connecting the pipes, Removing the connection pipe

Page 34

Refrigerant piping work

 

• When installing, make sure there is no leakage. When recovering the refrigerant, ground the compressor before

WARNING

removing the connection pipe.

• If the refrigerant pipe is not properly connected and the compressor works with the service valve open, the pipe

 

inhales the air and it makes the pressure inside of the refrigerant cycle abnormally high and it may cause explosion

 

and injury.

ffTry to keep the length of the refrigerant pipe as short as possible and make sure to minimize the height difference between the indoor and outdoor unit.

ffThe piping length between the outdoor unit and the indoor unit may not exceed the allowable piping length and height difference.

ffUse only certified refrigerant pipe and follow the installation method.

ffAfter completing the pipe installation, measure the length of the pipe to see whether or not you need to charge additional refrigerant. If you do, you must use R22 refrigerant.

ffUse clean refrigerant pipe with no harmful ion, oxide, dust, iron content or moisture inside pipe.

Connecting the pipes

1.There are holes for refrigerant pipes on the left, right and rear side of the indoor unit and you may choose any one of the holes depending on your installation location. Choose a side for the easier pipe connection. You may connect the drain hose through the hole in the middle part of the rear side on the indoor unit.

• Do not use a hammer, but use a cutter to cut the notch.

CAUTION

ENGLISH

Holes for refrigerant pipe

Holes for drain hose

2.Pipe installation condition may vary depending on the installation location. Therefore, use indoor and outdoor unit elbow pipe connector to install the pipe if necessary.

-- Allowable pipe length: Maximum 50m

-- Allowable pipe height difference: Maximum 20~30m

-- Make sure that there are less than 10 bending points in a pipe.

-- During initial installation, fill the additional refrigerant if the pipe length exceeds 5 m. -- For every 1 m of exceeding pipe length, fill additional refrigerant as stated below.

Model

 

Refrigerant amount

 

 

 

Basic (g)

 

Additional (g/m)

 

 

 

 

 

 

AP0AS0A✴✴✴

6,500

 

80

 

 

 

 

AP80S0A✴✴✴

4,500

 

80

 

 

 

 

Ex) If total piping length is 30 m,

6,500 g (standard filling amount for 5 m pipe): Factory default (AP0AS0A✴✴✴)

2,000 g {80 g/m x (30 m – 5 m)}: Additional refrigerant amount (Fill during the installation)

8,500 g: Total amount of refrigerant filling

33

PAC_아프리카 중동향AP80S0A_IBIM_34514A-02_EN.indd 33

2015-04-23 오후 2:18:58

Image 34
Contents Questions or COMMENTS? 08000-7267864Air Conditioner Thank you for purchasing this Samsung productFeatures of your new air conditioner ContentsXXFailing to do so may result in electric shock or fire Safety precautionsImportant safety symbols and precautions XXThis may result in electric shock or fireFor Power Supply XXWhen there is fire, this may cause spread of fireDo not operate the appliance with wet hands Do not place objects or devices under the indoor unitXXThis may result in electric shock Do not clean the inside of the air conditioner by yourself Do not drink the water from the air conditionerOperational temperature and humidity range Using outdoor unitChecking the auxiliary power switch Auxiliary power switch Elcb Earth Leakage Circuit BreakerMain parts Viewing the partsTo open the panel Locking the control panel Control panel and the displayUsing the air conditioner with the control panel Remote controller button Checking the remote controllerInstalling the batteries Auto Basic operationCool DryPress Button to adjust the desired temperature Press Button to start the operation of the air conditionerPress Adjusting the air flow directionTurbo operation Operation will operate for 30 minutesSmart saver operation Timer functionPress the button when the air conditioner is on You can turn the air conditioner off at your desired timeCleaning the outdoor unit heat exchanger Cleaning and maintaining the air conditionerCleaning the indoor unit Service centerCleaning the air filter Maintaining the air conditioner Periodical checksTroubleshooting Clean the air filter if it is dirty If the message See if the timer is already setFunction Accessing its internal components Installing the unitGeneral information Make sure that you earth the cables Power supply line, fuse or circuit breakerDo not install the air conditioner in following places Complete, electric shock or fire may occurWhen moving with a fork lift Preparation for installationWhen moving with a crane Indoor outdoor unit type and combinationDeciding on where to install the product Indoor unitOutdoor unit Fix the wire on the groundWires on the wall Personal injury or property damageSelecting appropriate location for installation Wear protective goggles and mask before spraying When 3 sides of the outdoor unit are blocked by the wall When there are no tall obstacles around the outdoor unitWhen the air outlet is opposite the wall Space requirementsWhen installing 1 outdoor unit When there is tall obstacle around the outdoor unitPipe length between the indoor and the outdoor unit Installing the outdoor unit in harsh environments Preparing the installationInstalling duct for horizontal exhaust discharge When installing ductsInstalling indoor unit Installing outdoor unit AP80S0XOutdoor unit base mount and anchor bolt position Removing the connection pipe Connecting the pipesRefrigerant piping work InjuryOutdoor unit pipe connection AP80S0X Keep the pipe length as short as possibleModel name Liquid side mm Gas side mm Selecting refrigerant pipeTemper grade and minimum thickness of the refrigerant pipe Outer diameter mm/inch Minimum thickness mm Temper gradeNitrogen flushing brazing Direction of the pipe when brazingStoring refrigerant pipe Stored place Stored time Sealing typeOuter diameter Dmm Cutting or flaring the pipesCorrect Inclined Damaged surface Cracked Uneven thickness Pipe bending Connecting the drain hoseTightening flare connection part Piping materialFfPipe insulation Selecting the insulator of the refrigerant pipeInsulating refrigerant pipe To prevent moisture from enteringWiring work Electrical workPower supply and wire specification 0Not includedConnecting power and communication cable AP80S0A / AP0AS0ASelecting solderless ring terminal Fixing the power cable Connecting the power terminalScrew Tightening torque kgf∙cm When using the exclusive terminal for grounding Grounding the power cableFfGrounding must be done by installation specialist Grounding workFfMake sure that grounding work is done in below procedure Grounding work procedureIf you are using the grounding on the switching board Procedure ExplanationGas leak test and vacuum drying Refrigerant charging How to add refrigerantAllowable refrigerant pipe length Setting the main PCB option Setting the option switches & function keysSetting the option switch of the indoor unit K1 K2 K3 K4Segment display Setting the outdoor unit KEYK2 Number of pressing Display PressingCheck lists after completing the installation Trial operation Trial operationInspection before trial operation Make sure that all the indoor units are properly operatingError display Error description Error diagnosisError display LED displayHow to connect your extended power cables Twist the wire cores together and push it in to the sleeveInsulation tape

AP0AS0ANXSG specifications

The Samsung AP0AS0ANXSG is a cutting-edge appliance that showcases the brand's commitment to innovation and excellence in technology. As a prominent player in the consumer electronics market, Samsung continues to push the boundaries of what is possible, and the AP0AS0ANXSG is a testament to that ethos.

One of the standout features of the AP0AS0ANXSG is its advanced energy efficiency. This appliance utilizes state-of-the-art technologies to consume less power while delivering exceptional performance. With energy-saving modes and automatic adjustments based on usage patterns, it not only minimizes electricity costs but also reduces environmental impact, aligning with sustainable living practices.

The appliance incorporates SmartThings technology, allowing users to control and monitor it remotely through their smartphones. This integration provides unparalleled convenience, enabling users to adjust settings, receive alerts, and even troubleshoot issues while away from home. The seamless connectivity enhances user experience, making it easier than ever to fit modern appliances into a busy lifestyle.

Design-wise, the AP0AS0ANXSG boasts a sleek and modern aesthetic that complements any home décor. Its ergonomic features include easy-to-use controls and a user-friendly interface that simplifies operation. Additionally, its compact size makes it suitable for various living spaces without compromising on performance or capacity.

In terms of performance, the AP0AS0ANXSG excels in delivering high-quality results. Whether it's cooking, cleaning, or other functions, this appliance is engineered to perform efficiently and effectively. The latest technology ensures that tasks are completed quickly, saving users valuable time.

Safety features in the AP0AS0ANXSG are also noteworthy. With multiple safety mechanisms, users can have peace of mind while using the appliance. These features are essential in households with children or pets, enhancing overall safety without sacrificing convenience or functionality.

Moreover, the AP0AS0ANXSG is designed to last, utilizing durable materials and components that withstand regular use. Samsung's reputation for reliability is evident in the construction of this appliance, contributing to its longevity and sustained performance over time.

In summary, the Samsung AP0AS0ANXSG is an exemplary appliance that incorporates energy efficiency, smart technology, aesthetic appeal, safety features, and robust performance. It represents a blend of style and functionality, making it a worthwhile investment for consumers seeking advanced solutions in their homes. With its innovative approach, Samsung continues to lead the industry, offering products that align with contemporary needs and preferences.