Samsung AQV12PWCXCEE, AQV09PWCNEUR Mode, When the air conditioner is on and in cool/heat mode

Page 13

mode

For a comfortable sleep, the air conditioner will operate it Fall asleep Sound sleep Wake up from mode.

When the air conditioner is on and in cool/heat mode

1. Press the button on the remote controller.

indicator appears and Off timer indicator starts blinking on the remote controller display.

2. Press the Time Up or Time Down button to set the time.

You can set the time in half hourly unit from 30 minutes ~ 3 hours and hour unit from 3 hours ~ 12 hours.

Operating hour can be set from minimum 30 minutes to maximum

12 hours.

Default operation hour is set to 8 hours.

3. Press the Set button to active it on.

Off timer indicator stops blinking and reserved time will be displayed for 3 seconds. Then the air conditioner operates in good’sleep mode.

If you don’t press Set button within 10 seconds after pressing the or Time Up or Time Down button, the air conditioner will return to previous status. Check Off timer indicator and indicator on the indoor unit.

Cancel Press the Cancel button once again.

You can set the desired temperature by 1˚C in the range of 16˚C~30˚C.

Fan speed will be adjusted automatically according to the mode.

However, I f you selectmode while heating operation is on, you can adjust fan speed.

Air flow direction will be adjusted automatically according to the mode.

However, if you select mode while heating operation is on, you can adjust air flow direction.

ENGLISH

Temperature and fan speed changes in mode

Fall asleep: Eases you into sleep by dropping the temperature.

Sound sleep: Relaxes your body and raises your temperature slightly.

Wake up from mode: Allows you to wake up from comfortable intermittent air and it makes you feel refreshed.

• Set Off timer in

mode over 5 hours. You fell disturbed sleep if the

is set too short or long

because the default is set to 8-hour-operation.

 

If the mode is set less than 4 hours, the operation will stop at the same time.

If the mode is set over 5 hours, it will run as Wake up stage from the last one hour before it stops.

Recommended set temperature is between 25˚C~27˚C for cooling and 21˚C~23˚C for heating.

13

Image 13
Contents Page Contents Important safety symbols and precautions Safety precautionsFollow directions Wall socketFor Using For Cleaning Operation ranges Checking before useChecking the name of the parts Power buttonMain parts DisplayRemote controller buttons Checking the remote controllerBattery changing time Remote controller displayStoring the remote controller Inserting the batteriesBasic function Press Button to adjust the temperatureUsing the Turbo function Adjusting the air flow directionPress the Air swing button on the remote controller Vertical air flowPress the button on the remote controller When the air conditioner is on and in cool/heat modeMode Press the Time Up or Time Down button to set the timePress the On Timer/Off Timer button Setting the On/Off timerAdditional options available in On timer mode From the moment you have set the timer Using the Smart Saver functionIf the air conditioner is on If the air conditioner is off Turn off automaticallyUsing the Auto Clean function Using the Quiet functionWhen the air conditioner is turned on Cleaning the indoor unit Cleaning the air conditionerCleaning the outdoor unit heat exchanger Opening the panelRemoving the Air filter Cleaning the air filterOpen the panel and put the Air filter out Dry the Air filter in a ventilated areaPeriodical checks Maintaining the air conditionerTroubleshooting Flow movement changes. It is normal Outdoor unit Heat exchanger during Heat mode in winterConnection Included Models Remark General informationAQV09P, AQV12P, AQV18P, AQV24P Installing the unit Choosing the installation locationPower supply line, fuse or circuit breaker  a place where the air filter can be replaced easilyOutdoor Unit Where sulfide gas existsWhen installing more than 1 outdoor unit When installing 1 outdoor unitSpace Requirements for Outdoor Unit Top view Side viewAccessories in the indoor unit case AccessoriesAccessories in the outdoor unit case Optional accessories Fixing the installation plateTools required for installation General Tools Tools for test operationsCable specification Connecting the assembly cableConnecting the cable Installation Each wire is labeled with the corresponding terminal numberCut off the remaining foam insulation Smooth the cut edgesPass the pipe through the hole in the wall Cutting or extending the pipe Purging the indoor unitUnscrew the caps at the end of each pipe Put a flare nut slightly into the pipe and modify the flareCorrect Inclined Pipe 50 Pa. The joint must be accessible and serviceableCracked Outer DiameterDrain hose installation Connect a drain hose to the drain plug Purging the connected pipesEnsure that condensation draining is adequate Adding Refrigerant  the factory refrigerant charge of the product Please fill in with indelible ink1975 To check for gas leaks on the outdoor unit Performing the gas leak testsTo check for gas leaks on the indoor unit Leak test with nitrogen before opening valvesFixing the indoor unit in place Then place the indoor unit on the installation plateFixing the outdoor unit in place Final Check and Trial Operation Apply heat to the contraction tube to contract it How to connect your extended power cablesAfter tube contraction work is completed, wrap it with Insulation tape to finishPage Samsung 7267864, € 0.07/min 42 2702-201-24-18 05 133Air Conditioner
Related manuals
Manual 41 pages 50.29 Kb Manual 41 pages 10.61 Kb Manual 43 pages 43.79 Kb Manual 39 pages 33.67 Kb Manual 43 pages 50.37 Kb Manual 41 pages 45.51 Kb Manual 23 pages 13.22 Kb Manual 43 pages 9.83 Kb