Installation | Samsung AQV09PSDNSER, AQV09PWCNEUR, AQV12PWCXCEE

Samsung AQV09PSDNSER Each wire is labeled with the corresponding terminal number, Installation

Page 29

2 . Open the front grille.

3 . Remove the screw securing the connector cover.

4 . Pass the assembly cable through the rear of the indoor unit and connect the assembly cable to terminals. (Refer to the picture below)

• Each wire is labeled with the corresponding terminal number.

5 . Pass the other end of the cable through the 65mm hole in the wall.

6 . Close the connector cover by tightening the screw carefully.

7 . Close the front grille.

8 . Remove the terminal board cover on the side of the outdoor unit. 9. Connect the cables to the terminals as seen in the picture.

• Each wire is labeled with the corresponding terminal number.

Indoor unit
	AQVPC			AQVPB
	Indoor unit			Indoor unit
	Indoor unit				1(L)	2(N)	F1	F2
	N(1)	1	2		1(L)	2(N)	F1	F2
	N(1)	1	2
	N(1)N1	1	2		1(L)	2(N)	F1	F2
Outdoor unit	N(1)	1	2
	N(1)	1	2
				F1	F2
	N(1)	1	2		L	N
	N(1)	1	2
	Outdoor unit			Outdoor unit

• End of the wire must be circular.

• Also circular terminal must be matched with screw size in terminal black.

•After connecting the cables, make sure terminal numbers on the indoor/outdoor unit matches.

•Screws on terminal block must not be unscrewed with the torque less than 12kgf•cm.

10.Connect the grounding conductor to the grounding terminals.

11.Close the terminal board cover by tightening the screw carefully.

• In Russia and Europe, consult with the supply authority to determine the supply system impedance before

installation.

• Connect the wires firmly so that wires can not be pulled out easily. (If they are loose, it could cause burn-out of the wires.)

•Connect the wires according to color codes, referring to the wiring diagram.

•The power cable and the interconnection cable should be selected according to the specification in page 28.

ENGLISH

Image 29

Contents

Page Contents Important safety symbols and precautions Safety precautionsFollow directions Wall socketFor Using For Cleaning Operation ranges Checking before useChecking the name of the parts Power buttonMain parts DisplayRemote controller buttons Checking the remote controllerBattery changing time Remote controller displayStoring the remote controller Inserting the batteriesBasic function Press Button to adjust the temperatureUsing the Turbo function Adjusting the air flow directionPress the Air swing button on the remote controller Vertical air flowPress the button on the remote controller When the air conditioner is on and in cool/heat modeMode Press the Time Up or Time Down button to set the timeAdditional options available in On timer mode Setting the On/Off timerPress the On Timer/Off Timer button From the moment you have set the timer Using the Smart Saver functionIf the air conditioner is on If the air conditioner is off Turn off automaticallyWhen the air conditioner is turned on Using the Quiet functionUsing the Auto Clean function Cleaning the indoor unit Cleaning the air conditionerCleaning the outdoor unit heat exchanger Opening the panelRemoving the Air filter Cleaning the air filterOpen the panel and put the Air filter out Dry the Air filter in a ventilated areaPeriodical checks Maintaining the air conditionerTroubleshooting Connection Outdoor unit Heat exchanger during Heat mode in winterFlow movement changes. It is normal AQV09P, AQV12P, AQV18P, AQV24P General informationIncluded Models Remark Installing the unit Choosing the installation locationPower supply line, fuse or circuit breaker  a place where the air filter can be replaced easilyOutdoor Unit Where sulfide gas existsWhen installing more than 1 outdoor unit When installing 1 outdoor unitSpace Requirements for Outdoor Unit Top view Side viewAccessories in the outdoor unit case AccessoriesAccessories in the indoor unit case Optional accessories Fixing the installation plateTools required for installation General Tools Tools for test operationsConnecting the cable Connecting the assembly cableCable specification Installation Each wire is labeled with the corresponding terminal numberPass the pipe through the hole in the wall Smooth the cut edgesCut off the remaining foam insulation Cutting or extending the pipe Purging the indoor unitUnscrew the caps at the end of each pipe Put a flare nut slightly into the pipe and modify the flareCorrect Inclined Pipe 50 Pa. The joint must be accessible and serviceableCracked Outer DiameterDrain hose installation Ensure that condensation draining is adequate Purging the connected pipesConnect a drain hose to the drain plug Adding Refrigerant 1975 Please fill in with indelible ink the factory refrigerant charge of the product To check for gas leaks on the outdoor unit Performing the gas leak testsTo check for gas leaks on the indoor unit Leak test with nitrogen before opening valvesFixing the outdoor unit in place Then place the indoor unit on the installation plateFixing the indoor unit in place Final Check and Trial Operation Apply heat to the contraction tube to contract it How to connect your extended power cablesAfter tube contraction work is completed, wrap it with Insulation tape to finishPage Samsung 7267864, € 0.07/min 42 2702-201-24-18 05 133Air Conditioner

Related manuals

Samsung AQV09PSDNSER Each wire is labeled with the corresponding terminal number, Installation

• Each wire is labeled with the corresponding terminal number.

installation.