Desa HD-9240 manual Troubleshooting Guide, Technical Service, Do Not Send Products

Page 13

Troubleshooting Guide

SYMPTOM

POSSIBLE CAUSE

 

 

 

Lights will

1.

Light switch is turned off.

not come

2.

Flood light is loose or burned out.

on.

3.

Fuse is blown or circuit breaker is

 

 

turned off.

 

4.

Daylight turnoff is in effect. (Re-

 

 

check after dark).

 

5.

Incorrect circuit wiring, if this is a

 

 

new installation.

 

6.

Re-aim the sensor to cover de-

 

 

sired area.

Lights come

1.

Control may be installed in a rela-

on in

 

tively dark location.

daylight.

2.

Control is in Test. (Set control

 

 

switch to an ON-TIME position).

 

 

 

Lights come

1.

Control may be sensing small ani-

on for no

 

mals or automobile traffic. (Re-

apparent

 

aim sensor or use lens shield).

reason.

2.

Sensitivity is set too high. (Reduce

 

 

sensitivity. Turn Range Boost off).

 

 

 

Technical Service

SYMPTOM

POSSIBLE CAUSE

 

 

 

Lights stay

1.

A lamp is positioned too close to

on continu-

 

the sensor or pointed at objects

ously.

 

that causes the sensor to trigger.

 

 

(Aim the lamp away from the sen-

 

 

sor or objects).

 

2.

Control is pointed at a heat source

 

 

like an air vent, dryer vent, or brightly-

 

 

painted heat-reflective surface. (Re-

 

 

aim sensor. Turn Boost off).

 

 

Lights flash

1. Heat or light from the lamps may be

on and off.

 

turning the Light Control on and off.

 

 

(Aim lamps away from the sensor.

 

 

Turn Boost off).

 

2.

Reflected heat from other objects

 

 

are triggering the sensor. (Re-aim

 

 

sensor. Turn Boost off).

 

3.

Control is warming up. (Flashing is

 

 

normal under these conditions. Wait

 

 

1 minute for sensor to warm up).

 

4.

Control is in Test. (Set control switch

 

 

to an ON-TIME position).

 

 

 

(Do Not Send Products)

If you experience a problem, follow this guide. You may also want to visit our Web site at: www.desatech.com. If the problem persists, call* for assistance at 1-800-858-8501,7:30 AM to 4:30 PM CST (M-F). You may also write* to:

DESA Specialty Products™

P.O. Box 90004, Bowling Green, KY 42102-9004

*If contacting Technical Service, please have the following information available: Model Number, Date of Purchase, and Place of Purchase.

No Service Parts Available for this Product

595-5631-07

-13-

Image 13
Contents ALL Metal Motion Sensor Light Control Contents Introduction Enhanced Performance FeaturesFits All Junction Box Configurations Package ContentsAdditional Items Needed Wall Mount Eave Mount InstallationUniversal Adaptor Standard WiringControlling Non-Motion Sensing Fixtures Power Requirements VAC, 60 Hz SpecificationsFinish Mounting Sensing Angle . . . . . . . . Up toTurn on the circuit breaker and light switch Test and AdjustmentExpected Coverage AdjustmentsMaximum Range Least SensitiveMaximum Coverage Angle Operation Technical Service Troubleshooting GuideNo Service Parts Available for this Product Do Not Send ProductsLifetime Warranty Control DE LUZ Y Detector DE Movimiento Todo Hecho DE Metal Indice Características Mejoradas de Rendimiento IntroducciónArtículos adicionales que se necesitan Contenidos del PaqueteMontaje en pared Montaje en alero InstalaciónCableado Estándar Adaptador UniversalControl de los aparatos que no detectan movimiento Especificaciones Fin del MontajePrueba y Ajuste Cobertura Esperada Continuación de ajustesAlcance Máximo Lo menos sensible Lo más sensibleAngulo de Cobertura Máxima Decida quŽ lado de la placa translœcida desea cubrirFuncionamiento Servicio Técnico Guia de Investigacion de AveriasNo enviar los productos No hay piezas de servicio disponibles para este productoGarantía Permanente Commande d’éclairage tout métal à Détecteur de mouvement Table des matières Page Convient à tous les types de boîte De jonction Articles additionnels requisAU Disjoncteur Montage mural Montage sous avant-toitCâblage standard Adaptateur UniverselUne fois que vous avez dŽterminŽ les appareils Commande d’appareils d’éclairage sans détecteur de mouvementSpécifications Finir le montageAngle de dŽtection . . . . . JusquÕˆ Test et réglage Coverture prévue Test et réglage suitePortée maximale Moins sensibleAngle de couverture Maximum Fonctionnement Se remet en mode Auto ˆ lÕaubeActivez lÕintensificateur de Auto et ManuelGuide de dépannage Service TechniqueNenvoyez pas de produits Aucune pièce de rechange n’est disponible pour ce produitGarantie à vie