Heatiator C40 owner manual Fan Replacement Instructions, Removing the fan

Page 26

Fan Replacement Instructions

1.Remove the brick from the bottom of the fireplace and 3 of the back vertical bricks.

2.Remove the 2 screws from the access panel in the fire- box floor. See Figure 4.8.

3.Pry up the access panel using the screwdriver slot and completely remove the panel.

Removing the fan

1.Unplug the wire harness.

2.Lift fan from locating pins and remove. Repeat for second fan if necessary. See Figure 4.9.

3.Connect new fan wires to wire harness.

4. Before installing the fan, make sure the grommets are	Figure 4.10 Installing Fans
tightly in place. Insert the right fan and place over the
2 locating pins. Repeat for other fan. Figure 4.10

5.Re-install bottom panel or firebox access panel in reverse order as described above.

6Replace the brick that was removed.

7. Reconnect the power.

	Screws
	Screwdriver Slot
Figure 4.8	Accessing Fan Motor

Unplug wire harness before removing fan

Remove nut

and lift out fan

Figure 4.9 Fan Motor

Page 26

Heatilator • Constitution EPA Fireplace • 480-1091D

4/20/11

Image 26

Contents C40 Hot screen/mesh and glass doors will cause burnsListing Label Information/Location 009Safety Alert Key Table Of Contents Limited Lifetime Warranty Warranty Conditions Manufactured Home Approved Listing and Code ApprovalsAppliance Certification Non-Combustible Materials BTU & Efficiency Specifications Electrical CodesGlass Specifications Combustible MaterialsHot glass will cause burns Operating InstructionsUser GuideYour Fireplace General Information Baffle and Blanket PlacementFirebrick Placement Hardwood vs. Softwood Moisture contentWood Fuel SeasoningStoring Wood Outside AirSeasoned Wood Clear Space Near the Fireplace Glass DoorsOver-Firing Your Appliance Fire SafetySymptoms of Over-Firing Chimney FireKindling or 1st stage Starting a FireBurning Process 2nd stageSlide Air Control Slide Left to Stop Automatic Combustion Control ACCFinal stage Burning Guidelines Manual Timer OverrideBurn Rates OpacityDraft Problems TroubleshootingUnderstanding Vent Problems Factory-built Fireplaces Troubleshooting Diagnostics and Problem Solving Diagnostic Question Possible Causes of Condition SolutionsDon’t get enough/any heat. What can I do about it? Maintenance and Servicing the Fireplace General Maintenance Creosote Chimney CleaningDisposal of Ashes Care and Cleaning of Plated SurfacesGlass Cleaning Door and Door Gasket Maintenance Task List Replacement Maintenance Glass ReplacementFirebrick Replacement Fire Brick ConfigurationsFan Cord Location Baffle Removal and InstallationFan Replacement Fan Replacement Instructions Removing the fanTimer Assembly Replacement 11 Timer AssemblyTimer Removal & Replacement Linkage Arm Slider Control Rod20/11 Heatilator Constitution EPA Fireplace 480-1091D Service & Maintenance Log Date of Service Performed By Description of ServiceGetting Started Installer Guide Typical Fireplace SystemNegative Pressure Design and Installation ConsiderationsDraft Locating Fireplace & Chimney Frequently open doors Central heat outlets or returnsInspect Fireplace and Components Tools and Supplies NeededFireplace System Requirements Framing & Clearances Selecting Fireplace LocationsClearances Clearances to Combustible MaterialsFrame the Fireplace Optional Framing Construction / Reduced Mantel HeightElectrical Access and Wiring Diagram Fan Wiring DiagramInstallation of Fireplace Mm metal flex Fireplace Or rigid pipe Secure the Fireplace Place Protective Metal Hearth StripsChimney Assembly Chimney Requirements Chimney Termination RequirementsUsing Offsets/ Returns ExampleInstalling CAK4A and Flex Pipe Assemble the Chimney SectionsInstall Ceiling Firestops Installing Flex PipeInstall Attic Insulation Shield Secure the ChimneyInstall Flashing Double-check the Chimney AssemblyComplete Installation Cut out Hole in Roof13 Multiple Chimney Locations SL-300 Series Ceiling/Roof Thimble Consult local codes for framing detailsChase Installations Construct the ChaseInstall Termination Cap Install Fireplace & ChimneyInstall Chase Top ST375 Square Termination Cap TCT375 Terra Cotta Cap = 1/k x inches of thickness FinishingHearth Extension Raised Hearth Extension Framing Fireplace and Hearth Extension are flush on the floorCombustible Material Position the Hearth ExtensionFinishing Material Non-Combustible MaterialCardboard or Metal Template MantelNon-Combustible Sealant Material Non-Combustible Facing Material Installa Tion 13 Complete installationAccessories Heat Zone Kit OptionalRun Length Cut Pipe 40 ft 6-12m 4 wall Firescreen Constitution Fireplace DimensionsReference Materials Chimney Components Catalog Description Catalog No15-3/4 DTO134 Service Parts Part number list on following#3 Brick Set StockedDoor Handle Assembly Side viewThis page intentionally left blank Contact Information Do not Discard this Manual

Related manuals

Manual 71 pages 48.08 Kb