Heatiator C40 owner manual Non-Combustible Facing Material Installa Tion, Complete installation

Page 58

G.Non-Combustible Facing Material Installa-

tion

WARNING! Risk of Fire! Follow these instructions exactly.

Facing materials must be installed properly to prevent fire. No materials may be substituted without authorization by Hearth & Home Technologies

TOOLS NEEDED: Powered drill with #2 Phillips head bit; caulk- ing gun.

1in. (25mm) OVERLAP

 

Metal strips 2 in. (51mm) under edge of

 

Fireplace and Hearth Extension and 2 in.

 

(51mm) on both side of fireplace opening.

Figure 10.10

Nail or screw metal strips in place.

 

1.Secure the fireplace to the floor or wall framing studs at a minimum of two attachment points to prevent fur- ther movement of the fireplace. The same holes and L brackets that attached the fireplace to the pallet may be used to secure the fireplace to the sub flooring by using a minimum of two 1/4 in. x 2 in. lag bolts or equivalent. Refer to Figure 10.10 and install the two metal hearth strips at this time.

NOTE: All boards are pre-drilled for your conve- nience. Boards MUST be attached in the following order: bottom, top, and then the two sides.

2.Attach the bottom board to the bottom of the outer fire- place can with enclosed screws, ensuring the board is centered.

3.Center and attach the top board to the outer can and framing members.

4.Using the Super Calstick, run a light bead (1/8 in. mini- mum) on the butt edges of the top board. See Figure 10.11

5.Ensuring the top of the side pieces and the top board align, attach the side pieces to the outer can and fram- ing members.

6.Use a wet or dry towel or a soft brush to remove any dust or dirt from facing material. Apply a non-combusti- ble adhesive to attach tile, stone or other non-combus- tible finishing materials per manufacturer’s instructions.

7.The non-combustible Super Calstick may be used for sealing between the fireplace and the hearth exten- sion. Refer to Figure 10.12.

Top

Apply bead of

Board

Super Calstick to

 

edge here

Side

 

Board

 

Bottom

 

Board

Side

 

 

Board

Figure 10.11

 

Seal with non-combustible sealant

Figure 10.12

Figure10.13 Complete installation

Page 58

Heatilator • Constitution EPA Fireplace • 480-1091D

4/20/11

Page 57 Page 59
Image 58
Page 57 Page 59
Contents C40 Hot screen/mesh and glass doors will cause burnsListing Label Information/Location 009Safety Alert Key Table Of Contents Limited Lifetime Warranty Warranty Conditions Appliance Certification Listing and Code ApprovalsManufactured Home Approved Non-Combustible Materials BTU & Efficiency Specifications Electrical CodesGlass Specifications Combustible MaterialsYour Fireplace Operating InstructionsUser GuideHot glass will cause burns Firebrick Placement Baffle and Blanket PlacementGeneral Information Hardwood vs. Softwood Moisture contentWood Fuel SeasoningSeasoned Wood Outside AirStoring Wood Clear Space Near the Fireplace Glass DoorsOver-Firing Your Appliance Fire SafetySymptoms of Over-Firing Chimney FireKindling or 1st stage Starting a FireBurning Process 2nd stageFinal stage Automatic Combustion Control ACCSlide Air Control Slide Left to Stop Burning Guidelines Manual Timer OverrideBurn Rates OpacityUnderstanding Vent Problems TroubleshootingDraft Problems Factory-built Fireplaces Troubleshooting Diagnostics and Problem Solving Diagnostic Question Possible Causes of Condition SolutionsDon’t get enough/any heat. What can I do about it? Maintenance and Servicing the Fireplace General Maintenance Creosote Chimney CleaningDisposal of Ashes Care and Cleaning of Plated SurfacesGlass Cleaning Door and Door GasketMaintenance Task List Replacement Maintenance Glass ReplacementFirebrick Replacement Fire Brick ConfigurationsFan Replacement Baffle Removal and InstallationFan Cord Location Fan Replacement Instructions Removing the fanTimer Assembly Replacement 11 Timer AssemblyTimer Removal & Replacement Linkage Arm Slider Control Rod20/11 Heatilator Constitution EPA Fireplace 480-1091D Service & Maintenance Log Date of Service Performed By Description of ServiceGetting Started Installer Guide Typical Fireplace SystemDraft Design and Installation ConsiderationsNegative Pressure Locating Fireplace & Chimney Frequently open doors Central heat outlets or returnsFireplace System Requirements Tools and Supplies NeededInspect Fireplace and Components Framing & Clearances Selecting Fireplace LocationsClearances Clearances to Combustible MaterialsFrame the Fireplace Optional Framing Construction / Reduced Mantel HeightElectrical Access and Wiring Diagram Fan Wiring DiagramInstallation of Fireplace Mm metal flex Fireplace Or rigid pipe Secure the Fireplace Place Protective Metal Hearth StripsChimney Assembly Chimney Requirements Chimney Termination RequirementsUsing Offsets/ Returns ExampleInstalling CAK4A and Flex Pipe Assemble the Chimney SectionsInstall Ceiling Firestops Installing Flex PipeInstall Attic Insulation Shield Secure the ChimneyInstall Flashing Double-check the Chimney AssemblyComplete Installation Cut out Hole in Roof13 Multiple Chimney Locations SL-300 Series Ceiling/Roof Thimble Consult local codes for framing detailsChase Installations Construct the ChaseInstall Chase Top Install Fireplace & ChimneyInstall Termination Cap ST375 Square Termination Cap TCT375 Terra Cotta Cap Hearth Extension Finishing= 1/k x inches of thickness Raised Hearth Extension Framing Fireplace and Hearth Extension are flush on the floorCombustible Material Position the Hearth ExtensionFinishing Material Non-Combustible MaterialNon-Combustible Sealant Material MantelCardboard or Metal Template Non-Combustible Facing Material Installa Tion 13 Complete installationAccessories Heat Zone Kit OptionalRun Length Cut Pipe 40 ft 6-12m 4 wall Firescreen Reference Materials Fireplace DimensionsConstitution Chimney Components Catalog Description Catalog No15-3/4 DTO134 Service Parts Part number list on following#3 Brick Set StockedDoor Handle Assembly Side viewThis page intentionally left blank Contact Information Do not Discard this Manual
Related manuals
Manual 71 pages 48.08 Kb

C40 specifications

The Heatiator C40 is an innovative heating solution designed to optimize comfort and energy efficiency in residential and commercial spaces. This advanced heating unit combines modern technology with user-friendly features, making it an excellent choice for anyone looking to improve their heating systems.

One of the standout features of the Heatiator C40 is its powerful heating capacity. With an output of up to 40,000 BTUs, this unit is capable of efficiently warming large areas, ensuring that no space is left cold. The C40 utilizes high-efficiency burners that maximize heat output while minimizing fuel consumption. This not only translates to lower energy bills for the consumer but also contributes to a reduced carbon footprint.

The Heatiator C40 is equipped with advanced smart technology, allowing users to control their heating environment remotely. With the Heatiator mobile app, users can adjust the temperature settings, set schedules, and monitor energy usage from their smartphones. This level of control ensures that comfort is maintained without unnecessary energy waste.

Another notable characteristic of the C40 is its versatile design. The unit can be easily installed in various configurations, including wall-mounted, freestanding, or built-in options, making it suitable for any room layout or decor. Its sleek, compact design also ensures that it blends seamlessly into any environment, providing users with both functionality and aesthetic appeal.

Safety is a priority in the design of the Heatiator C40. The unit is equipped with multiple safety features, including overheat protection, a flame failure device, and an automatic shut-off system. These safety measures provide peace of mind, allowing users to enjoy their heating without worry.

Furthermore, the Heatiator C40 operates quietly, making it an ideal choice for bedrooms and living areas where noise can be a distraction. The noise-reduction technology incorporated into the unit ensures that the heating process is unobtrusive, allowing for a peaceful environment.

In summary, the Heatiator C40 is a cutting-edge heating solution that stands out due to its powerful performance, energy efficiency, and user-friendly technology. With its stylish design, safety features, and advanced controls, the C40 is an excellent investment for anyone looking to enhance their heating system while enjoying the comfort of a warm, inviting space. Whether for homes or businesses, the Heatiator C40 promises reliable performance and satisfaction.
Top Page Image Contents