Delta 45, F-25, 35, 30, 40 warranty Storage Tank Application, Multiple Units Installation

Page 18

Domestic Piping

3.Solder the U-Tube Assembly onto the adapter. (See Fig. 1)

4.Once the adapter has sufficiently cooled, re-insert the check valve assem- bly making sure of orientation and reconnect onto the mixing valve.

If the installation of the ELITE requires domestic hot water for a commercial dish- washer, the installer may insert a tee con- nection between the unit and the mixing valve to provide 140ºF domestic hot water. The installer must reference local plumbing codes to ensure if this type of application is permissible.

DANGER

The thermostatic mixing valve MUST be installed and utilized on the ELITE. Removal of the thermostatic mixing valve will result in severe personal injury or death.

CAUTION

The installer should remove the thermostatic mixing valve from the units and install a single thermostatic mixing valve at the outlet of the hot water manifold. The thermostatic mixing valve should be sized according to the required flow rate and pressure drop. Refer to the ther- mostat mixing valve manufacturer specifica- tion and installation instructions for more details.

Reference Fig. 4, page 15 for piping diagram.

Storage Tank Application

For applications requiring large volumes of domestic hot water in a relative short period, the installer may include a storage type tank (see Fig. 5 page 16) in the domestic piping. The installer must:

1.Relocate the thermostatic mixing valve from the ELITE to the outlet of the stor- age tank.

2.Provide recirculation from the storage tank back to the ELITE using a bronze type circulator. Maximum recommend- ed flow rate is 5 to 10 gpm.

The manual valve on the U-Tube assem- bly must remain in the full open position for proper operation of the thermostatic mixing valve.

Domestic Drain Valve

-The installer must install a drain valve and drain leg as shown in Fig. 2 page 14 or Fig. 3 page 15.

-The drain valve should be positioned close to the floor to aid in the siphon action required to drain the inner tank.

Multiple Units Installation

For applications using multiple units the domestic piping should be piped using a bal- anced manifold arrangement.

Check Valve

 

Adapter

ot

H

U-Tube Assembly

 

Cold

 

 

Mixed

Fig. 1: Mixing Valve Assembly

 

13

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Installation a N D M a I N T E N a N C E For Your SafetyTable of Contents Section V Primary Piping Section Viii Internal Wiring Section Xiii CHECK-OUT Procedures Product & Safety Information HOT Ber and the serial number from the rat Ing label when inquiring about service orTroubleshooting Triangle Tube accepts no liability for anyOperating Restrictions Code Compliance Section I Pre-Installation ItemsBoiler Replacement Determining Product LocationResidential Garage Installations Section II Providing Air for Combustion and Ventilation Removal of an Existing Boiler from a Common Vent System Handling Instructions Hydrostatic Test ProceduresSection III Unit Preparation Hydrostatic Pressure TestCompletion of Hydrostatic Test and Draining General Piping Requirements Temperature / Pressure Relief ValveSection IV Domestic Piping Domestic Supply PressureDomestic Piping Multiple Units Installation Storage Tank ApplicationDomestic Piping Diagrams TR/SMART Series ApplicationElite With Recirculation Domestic Piping Elite with Storage TankSection V Primary Piping Closet Zero Clearance Applications Sizing Primary PipingSystem Piping Zone Circulators Primary Piping Near Appliance Piping Install balancing valves to Primary Piping Low Temperature Radiant System Primary Piping Multi Units Installation Section VI Venting Repair any damaged chimney mor- tar or jointsOil Vent Direct Vent Applications Gas Venting -General Requirements Masonry and Metal ChimneysType B Vent Systems Vent Connectors Section VII Fuel Piping Recommended Gas Supply PipingPipe Sizing Propane Gas Pipe Sizing Natural GasNatural Gas Supply Pressure Requirements Propane Gas Supply Pressure RequirementsGeneral Oil Piping Guidelines Section Viii Internal Wiring Elite Factory Internal WiringWire Color Code Outdoor Temperature Limit Section IX External WiringInstallation Compliance Line Voltage ConnectionsMultiple Zone Field Wiring Using Zone Valves Field wiring with zone circulators Typical Zone Relay Panel Wiring Section X Start Up Preparation Filling the Outer Primary Tank and System Check Low Water Cut-Off Device Section XI Start-Up Procedures Final Checks Before Start-upElite Start-up Recommended Combustion Levels Section XII Temperature Limits Recommended Primary Thermostat SettingTemperature Limits Section XIII- Check-Out Procedures Section XIV Installation Record Section Xvii Replacement Parts Jacket Components Control Panel Components Electrical Panel Components Specifications Elite Data TTP Brazed Plate Heat Exchangers Maxi-flo Pool and Spa Heat Exchangers

45, 30, 35, 40, F-25 specifications

Delta 40, F-25, F-30, F-35, and F-45 represent a new generation of aircraft designed to meet the evolving demands of modern aviation. These aircraft are equipped with advanced technologies, making them suitable for various missions, including cargo transport, surveillance, and multirole combat operations. Each model in this series comes with its own set of features and capabilities.

The Delta 40 stands as a versatile platform known for its impressive range and payload capacity. Its advanced avionics system ensures enhanced situational awareness and operational efficiency. The aircraft employs composite materials for improved fuel efficiency and reduced maintenance costs. Furthermore, Delta 40 is equipped with state-of-the-art navigation systems that include GPS, inertial navigation, and terrain awareness features.

The F-25 is designed with a focus on agility and speed. It features advanced thrust vectoring technology that allows for greater maneuverability, making it effective in air-to-air combat situations. The aircraft leverages stealth technology, incorporating radar-absorbing materials that reduce its visibility to enemy radar systems. This model also includes advanced electronic warfare capabilities for defensive operations.

Moving on to the F-30, this aircraft serves as a heavy-lift solution, optimized for cargo transport. Its spacious cargo bay can accommodate a wide range of freight, and its loading ramp facilitates quick turnaround times for ground operations. The F-30 utilizes a fly-by-wire control system to enhance stability and control during flight. Additionally, this model is equipped with advanced communication systems that allow for seamless integration into joint operations.

The F-35 integrates cutting-edge technologies to provide multirole capabilities. It boasts an advanced sensor suite that enables real-time data sharing among allied forces. The aircraft's stealth capabilities and advanced electronic warfare systems make it a formidable presence on the battlefield. Its interoperability with various platforms enhances the overall effectiveness of joint missions.

Finally, the F-45 combines the best features of its predecessors and introduces several enhancements. It leverages artificial intelligence for mission planning and execution, streamlining complex operations. The aircraft is also equipped with the latest in propulsion technology, resulting in improved fuel efficiency and performance at high altitudes.

Each of these aircraft models is designed with specific missions in mind, showcasing a commitment to innovation and technological advancement in aviation. With features that enhance their performance, adaptability, and combat readiness, the Delta 40, F-25, F-30, F-35, and F-45 represent the future of aviation technology. Their development signifies an important step toward maintaining technological superiority in both military and commercial aviation sectors.
Top Page Image Contents