Delta 45, F-25, 35 Section IX External Wiring, Installation Compliance, Line Voltage Connections

Page 38

External Wiring

SECTION IX - External Wiring

Installation Compliance

All field wiring made during installation must comply with:

-National Electrical Code NFPA 70 and any other national, state, provincial or local codes or requirements.

-In Canada, CSA C22.1 Canadian Electrical Code Part 1, and any other local codes.

Line Voltage Connections

1.Connect 120 VAC power wire to the line voltage leads located behind the front con- trol panel.

2.Route the incoming 120 VAC power wire through the right side jacket panel.

3.Use the wire nuts provided to ensure a tight and secure connection.

4.The unit is provided with a service switch, check local code requirements for compli- ance.

NOTICE

If local electrical codes or conditions require an additional service switch, the installer must provide and install a fused disconnect or 15 amp (minimum) service switch.

Thermostat Wiring

1.Connect room thermostat or the end switch (isolated contact only) of a relay control panel to the Room Thermostat Snap-set located on the rear jacket panel.

2.Remove the snap-set cover and connect the thermostat wiring to terminals C and 1 per Fig. 17.

3.For proper operation install the room ther- mostat on an inside wall away from influ-

ences of heat and cold, i.e. water pipes, areas of draft, lighting fixtures and fire- places.

4.Set the thermostat anticipator (if applica- ble) as follows:

-Set for 0.2 amps when wired directly to the Room Thermostat Snap-set.

-Set to match the total electrical power requirements of the connected devices when wired to zone relays or other devices. Refer to the relay manufactur- ers’ specifications and the thermostat instructions for additional information on the anticipator setting.

Outdoor Temperature Limit

1.The ELITE may operate with a variable primary operating temperature using an outdoor reset control provided by the installer.

2.Remove the factory jumper across termi- nals 9 and 10 of the wiring terminal. Connect the outdoor limit control to those terminals.

3.Set the operating limits of the outdoor limit control as follows:

-Maximum operating temperature of 180ºF.

-Minimum operating temperature of 150ºF.

Fig. 17: Room Thermostat Snap-set Wiring

33

Image 38
Contents Installation a N D M a I N T E N a N C E For Your SafetyTable of Contents Section V Primary Piping Section Viii Internal Wiring Section Xiii CHECK-OUT Procedures Product & Safety Information HOT Ber and the serial number from the rat Ing label when inquiring about service orTroubleshooting Triangle Tube accepts no liability for anyOperating Restrictions Code Compliance Section I Pre-Installation ItemsBoiler Replacement Determining Product LocationResidential Garage Installations Section II Providing Air for Combustion and Ventilation Removal of an Existing Boiler from a Common Vent System Handling Instructions Hydrostatic Test ProceduresSection III Unit Preparation Hydrostatic Pressure TestCompletion of Hydrostatic Test and Draining General Piping Requirements Temperature / Pressure Relief ValveSection IV Domestic Piping Domestic Supply PressureDomestic Piping Multiple Units Installation Storage Tank ApplicationDomestic Piping Diagrams TR/SMART Series ApplicationElite With Recirculation Domestic Piping Elite with Storage TankSection V Primary Piping System Piping Zone Circulators Closet Zero Clearance ApplicationsSizing Primary Piping Primary Piping Near Appliance Piping Install balancing valves to Primary Piping Low Temperature Radiant System Primary Piping Multi Units Installation Section VI Venting Repair any damaged chimney mor- tar or jointsOil Vent Direct Vent Applications Type B Vent Systems Gas Venting -General RequirementsMasonry and Metal Chimneys Vent Connectors Section VII Fuel Piping Recommended Gas Supply PipingPipe Sizing Propane Gas Pipe Sizing Natural GasNatural Gas Supply Pressure Requirements Propane Gas Supply Pressure RequirementsGeneral Oil Piping Guidelines Section Viii Internal Wiring Elite Factory Internal WiringWire Color Code Outdoor Temperature Limit Section IX External WiringInstallation Compliance Line Voltage ConnectionsMultiple Zone Field Wiring Using Zone Valves Field wiring with zone circulators Typical Zone Relay Panel Wiring Section X Start Up Preparation Filling the Outer Primary Tank and System Check Low Water Cut-Off Device Elite Start-up Section XI Start-Up ProceduresFinal Checks Before Start-up Recommended Combustion Levels Section XII Temperature Limits Recommended Primary Thermostat SettingTemperature Limits Section XIII- Check-Out Procedures Section XIV Installation Record Section Xvii Replacement Parts Jacket Components Control Panel Components Electrical Panel Components Specifications Elite Data TTP Brazed Plate Heat Exchangers Maxi-flo Pool and Spa Heat Exchangers

45, 30, 35, 40, F-25 specifications

Delta 40, F-25, F-30, F-35, and F-45 represent a new generation of aircraft designed to meet the evolving demands of modern aviation. These aircraft are equipped with advanced technologies, making them suitable for various missions, including cargo transport, surveillance, and multirole combat operations. Each model in this series comes with its own set of features and capabilities.

The Delta 40 stands as a versatile platform known for its impressive range and payload capacity. Its advanced avionics system ensures enhanced situational awareness and operational efficiency. The aircraft employs composite materials for improved fuel efficiency and reduced maintenance costs. Furthermore, Delta 40 is equipped with state-of-the-art navigation systems that include GPS, inertial navigation, and terrain awareness features.

The F-25 is designed with a focus on agility and speed. It features advanced thrust vectoring technology that allows for greater maneuverability, making it effective in air-to-air combat situations. The aircraft leverages stealth technology, incorporating radar-absorbing materials that reduce its visibility to enemy radar systems. This model also includes advanced electronic warfare capabilities for defensive operations.

Moving on to the F-30, this aircraft serves as a heavy-lift solution, optimized for cargo transport. Its spacious cargo bay can accommodate a wide range of freight, and its loading ramp facilitates quick turnaround times for ground operations. The F-30 utilizes a fly-by-wire control system to enhance stability and control during flight. Additionally, this model is equipped with advanced communication systems that allow for seamless integration into joint operations.

The F-35 integrates cutting-edge technologies to provide multirole capabilities. It boasts an advanced sensor suite that enables real-time data sharing among allied forces. The aircraft's stealth capabilities and advanced electronic warfare systems make it a formidable presence on the battlefield. Its interoperability with various platforms enhances the overall effectiveness of joint missions.

Finally, the F-45 combines the best features of its predecessors and introduces several enhancements. It leverages artificial intelligence for mission planning and execution, streamlining complex operations. The aircraft is also equipped with the latest in propulsion technology, resulting in improved fuel efficiency and performance at high altitudes.

Each of these aircraft models is designed with specific missions in mind, showcasing a commitment to innovation and technological advancement in aviation. With features that enhance their performance, adaptability, and combat readiness, the Delta 40, F-25, F-30, F-35, and F-45 represent the future of aviation technology. Their development signifies an important step toward maintaining technological superiority in both military and commercial aviation sectors.