Delta F-25, 35, 30, 45 Section XI Start-Up Procedures, Final Checks Before Start-up, Elite Start-up

Page 45

Start-Up Procedures

SECTION XI - Start-Up Procedures

Final Checks Before Start-up

Verify the ELITE and the primary and domestic systems are full of water and all system components are correctly set for operation.

Verify Start-up Preparation items outlined on pages 37 thru 39 have been completed.

Verify all electrical connections are correct and securely fasten.

Inspect vent piping and combustion air inlet piping for signs of deterioration from corrosion, physical damage or sagging. Verify combustion air piping and vent pip- ing are intact and correctly installed.

Adjustment of the Secondary Thermostat Limit.

The Secondary (Domestic) Thermostat located on left side of the control panel maintains the minimum domestic water storage temperature.

Set the thermostat knob as shown in Fig. 22 page 42.

Maximum limit setting is 140ºF

ELITE Start-up

Turn the ON-OFF switch located on the front control panel to the OFF position. Turn the electrical supply or any service switch to the unit in the ON position.

Check Domestic Piping.

Check domestic piping and system components for leaks. If found, shut down the unit and repair immediately.

Check Primary Piping.

Check primary system piping and com- ponents for leaks. If found, shut down the unit and repair immediately.

Purge any remaining air from the system piping. Air in the system piping will

interfere with circulation creating heat distribution problems and system noise.

Check Vent Piping

Check for gas-tight seal at every connec- tion and seam of the venting.

WARNING

Venting system must be sealed gas-tight to prevent flue gas spillage and potential carbon monoxide emissions, which will result in severe personal injury or death.

Check Gas Piping (if applicable)

1.Check around the unit for gas odor fol- lowing the procedure outlined in this manual on Page 39.

WARNING

If any gas leaks are found or suspected, shut the unit down immediately. Use a gas detection device or bubble test to locate the source of the gas leak and repair at once. Do not operate the unit until the leak is corrected. Failure to comply with this procedure could result in severe personal injury, death or sub- stantial property damage.

Check Oil piping (if applicable)

Check for any leakage at the pump and all fittings

Verify Flame Pattern and Combustion

Check the flame pattern through the inspection port of the burner. The flame should be stable.

Test for CO2 or O2 and for CO. The combustion reading should be within the range listed in Table 2 page 41. The CO level should not exceed 100 ppm when combustion is correct.

40

Page 44 Page 46
Image 45
Page 44 Page 46
Contents For Your Safety Installation a N D M a I N T E N a N C ETable of Contents Section V Primary Piping Section Viii Internal Wiring Section Xiii CHECK-OUT Procedures Product & Safety Information HOT Troubleshooting Ing label when inquiring about service orBer and the serial number from the rat Triangle Tube accepts no liability for anyOperating Restrictions Boiler Replacement Section I Pre-Installation ItemsCode Compliance Determining Product LocationResidential Garage Installations Section II Providing Air for Combustion and Ventilation Removal of an Existing Boiler from a Common Vent System Section III Unit Preparation Hydrostatic Test ProceduresHandling Instructions Hydrostatic Pressure TestCompletion of Hydrostatic Test and Draining Section IV Domestic Piping Temperature / Pressure Relief ValveGeneral Piping Requirements Domestic Supply PressureDomestic Piping Storage Tank Application Multiple Units InstallationTR/SMART Series Application Domestic Piping DiagramsElite With Recirculation Elite with Storage Tank Domestic PipingSection V Primary Piping Closet Zero Clearance Applications Sizing Primary PipingSystem Piping Zone Circulators Primary Piping Near Appliance Piping Install balancing valves to Primary Piping Low Temperature Radiant System Primary Piping Multi Units Installation Repair any damaged chimney mor- tar or joints Section VI VentingOil Vent Direct Vent Applications Gas Venting -General Requirements Masonry and Metal ChimneysType B Vent Systems Vent Connectors Recommended Gas Supply Piping Section VII Fuel PipingNatural Gas Supply Pressure Requirements Pipe Sizing Natural GasPipe Sizing Propane Gas Propane Gas Supply Pressure RequirementsGeneral Oil Piping Guidelines Elite Factory Internal Wiring Section Viii Internal WiringWire Color Code Installation Compliance Section IX External WiringOutdoor Temperature Limit Line Voltage ConnectionsMultiple Zone Field Wiring Using Zone Valves Field wiring with zone circulators Typical Zone Relay Panel Wiring Section X Start Up Preparation Filling the Outer Primary Tank and System Check Low Water Cut-Off Device Section XI Start-Up Procedures Final Checks Before Start-upElite Start-up Recommended Combustion Levels Recommended Primary Thermostat Setting Section XII Temperature LimitsTemperature Limits Section XIII- Check-Out Procedures Section XIV Installation Record Section Xvii Replacement Parts Jacket Components Control Panel Components Electrical Panel Components Specifications Elite Data Maxi-flo Pool and Spa Heat Exchangers TTP Brazed Plate Heat Exchangers

45, 30, 35, 40, F-25 specifications

Delta 40, F-25, F-30, F-35, and F-45 represent a new generation of aircraft designed to meet the evolving demands of modern aviation. These aircraft are equipped with advanced technologies, making them suitable for various missions, including cargo transport, surveillance, and multirole combat operations. Each model in this series comes with its own set of features and capabilities.

The Delta 40 stands as a versatile platform known for its impressive range and payload capacity. Its advanced avionics system ensures enhanced situational awareness and operational efficiency. The aircraft employs composite materials for improved fuel efficiency and reduced maintenance costs. Furthermore, Delta 40 is equipped with state-of-the-art navigation systems that include GPS, inertial navigation, and terrain awareness features.

The F-25 is designed with a focus on agility and speed. It features advanced thrust vectoring technology that allows for greater maneuverability, making it effective in air-to-air combat situations. The aircraft leverages stealth technology, incorporating radar-absorbing materials that reduce its visibility to enemy radar systems. This model also includes advanced electronic warfare capabilities for defensive operations.

Moving on to the F-30, this aircraft serves as a heavy-lift solution, optimized for cargo transport. Its spacious cargo bay can accommodate a wide range of freight, and its loading ramp facilitates quick turnaround times for ground operations. The F-30 utilizes a fly-by-wire control system to enhance stability and control during flight. Additionally, this model is equipped with advanced communication systems that allow for seamless integration into joint operations.

The F-35 integrates cutting-edge technologies to provide multirole capabilities. It boasts an advanced sensor suite that enables real-time data sharing among allied forces. The aircraft's stealth capabilities and advanced electronic warfare systems make it a formidable presence on the battlefield. Its interoperability with various platforms enhances the overall effectiveness of joint missions.

Finally, the F-45 combines the best features of its predecessors and introduces several enhancements. It leverages artificial intelligence for mission planning and execution, streamlining complex operations. The aircraft is also equipped with the latest in propulsion technology, resulting in improved fuel efficiency and performance at high altitudes.

Each of these aircraft models is designed with specific missions in mind, showcasing a commitment to innovation and technological advancement in aviation. With features that enhance their performance, adaptability, and combat readiness, the Delta 40, F-25, F-30, F-35, and F-45 represent the future of aviation technology. Their development signifies an important step toward maintaining technological superiority in both military and commercial aviation sectors.
Top Page Image Contents