Delta F-25, 35, 30, 45, 40 warranty Oil Vent Direct Vent Applications

Page 30

Venting

Install a barometric control device in the vent

- Note that prevailing winds could cause

connector as shown in Fig. 13 and 13A and

nuisance lockouts, freezing of conden-

adjust per the manufacturer’s instruction when

sate and water/ice build-up may occur

excess draft needs to be relieved or when

on buildings, plants and roofs.

applicable codes require a device.

 

Install an induced draft fan in the chimney for applications in which:

-Excessive resistance to the flow of flue gases is excepted

-The cross-sectional area of the chimney is smaller than the minimal area required

-The chimney height is less than the minimal requirement

When using an induced draft fan the installer should seal all vent joints and provide an inter- lock system for the ELITE to ensure fan oper- ation.

Oil Vent - Direct Vent Applications

The installer must read and comply with the direct vent instruction outline in Triangle Tube Oil-Fired Direct Vent Instructions.

The installer should give attention to the loca- tion of the ELITE prior to installation. The installer should:

-Locate the unit for shortest possible vent length and the most direct path to the outside wall.

-Note that flue gases will form a white plume in colder climates which may obstruct window views

The installer should consider the following when determining the location of the vent ter- mination:

-Locate or guard the vent termination in a manner to prevent accidental contact by people or pets.

-Vent must terminate at least 4 feet below and 4 feet horizontally or 1 foot above any window, door or gravity air inlet to the building.

-Vent must terminate not less than 7 feet above grade when located adjacent to a public sidewalk.

-Terminate the vent at least 6 feet from adjacent walls

-The bottom of the vent termination shall be located at least 1 foot above the grade, including normal snowline.

-DO NOT terminate the vent into win- dow wells, stairwells, alcoves, court- yards or other recess area.

-DO NOT terminate vent above any window, door or gravity inlet as con- densate can freeze causing ice forma- tions.

 

Oil Fired Installations

 

Damper

 

Damper

Fig. 13

Fig. 13A

25

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Installation a N D M a I N T E N a N C E For Your SafetyTable of Contents Section V Primary Piping Section Viii Internal Wiring Section Xiii CHECK-OUT Procedures Product & Safety Information HOT Ber and the serial number from the rat Ing label when inquiring about service orTroubleshooting Triangle Tube accepts no liability for anyOperating Restrictions Code Compliance Section I Pre-Installation ItemsBoiler Replacement Determining Product LocationResidential Garage Installations Section II Providing Air for Combustion and Ventilation Removal of an Existing Boiler from a Common Vent System Handling Instructions Hydrostatic Test ProceduresSection III Unit Preparation Hydrostatic Pressure TestCompletion of Hydrostatic Test and Draining General Piping Requirements Temperature / Pressure Relief ValveSection IV Domestic Piping Domestic Supply PressureDomestic Piping Multiple Units Installation Storage Tank ApplicationDomestic Piping Diagrams TR/SMART Series ApplicationElite With Recirculation Domestic Piping Elite with Storage TankSection V Primary Piping Closet Zero Clearance Applications Sizing Primary PipingSystem Piping Zone Circulators Primary Piping Near Appliance Piping Install balancing valves to Primary Piping Low Temperature Radiant System Primary Piping Multi Units Installation Section VI Venting Repair any damaged chimney mor- tar or jointsOil Vent Direct Vent Applications Gas Venting -General Requirements Masonry and Metal ChimneysType B Vent Systems Vent Connectors Section VII Fuel Piping Recommended Gas Supply PipingPipe Sizing Propane Gas Pipe Sizing Natural GasNatural Gas Supply Pressure Requirements Propane Gas Supply Pressure RequirementsGeneral Oil Piping Guidelines Section Viii Internal Wiring Elite Factory Internal WiringWire Color Code Outdoor Temperature Limit Section IX External WiringInstallation Compliance Line Voltage ConnectionsMultiple Zone Field Wiring Using Zone Valves Field wiring with zone circulators Typical Zone Relay Panel Wiring Section X Start Up Preparation Filling the Outer Primary Tank and System Check Low Water Cut-Off Device Section XI Start-Up Procedures Final Checks Before Start-upElite Start-up Recommended Combustion Levels Section XII Temperature Limits Recommended Primary Thermostat SettingTemperature Limits Section XIII- Check-Out Procedures Section XIV Installation Record Section Xvii Replacement Parts Jacket Components Control Panel Components Electrical Panel Components Specifications Elite Data TTP Brazed Plate Heat Exchangers Maxi-flo Pool and Spa Heat Exchangers

45, 30, 35, 40, F-25 specifications

Delta 40, F-25, F-30, F-35, and F-45 represent a new generation of aircraft designed to meet the evolving demands of modern aviation. These aircraft are equipped with advanced technologies, making them suitable for various missions, including cargo transport, surveillance, and multirole combat operations. Each model in this series comes with its own set of features and capabilities.

The Delta 40 stands as a versatile platform known for its impressive range and payload capacity. Its advanced avionics system ensures enhanced situational awareness and operational efficiency. The aircraft employs composite materials for improved fuel efficiency and reduced maintenance costs. Furthermore, Delta 40 is equipped with state-of-the-art navigation systems that include GPS, inertial navigation, and terrain awareness features.

The F-25 is designed with a focus on agility and speed. It features advanced thrust vectoring technology that allows for greater maneuverability, making it effective in air-to-air combat situations. The aircraft leverages stealth technology, incorporating radar-absorbing materials that reduce its visibility to enemy radar systems. This model also includes advanced electronic warfare capabilities for defensive operations.

Moving on to the F-30, this aircraft serves as a heavy-lift solution, optimized for cargo transport. Its spacious cargo bay can accommodate a wide range of freight, and its loading ramp facilitates quick turnaround times for ground operations. The F-30 utilizes a fly-by-wire control system to enhance stability and control during flight. Additionally, this model is equipped with advanced communication systems that allow for seamless integration into joint operations.

The F-35 integrates cutting-edge technologies to provide multirole capabilities. It boasts an advanced sensor suite that enables real-time data sharing among allied forces. The aircraft's stealth capabilities and advanced electronic warfare systems make it a formidable presence on the battlefield. Its interoperability with various platforms enhances the overall effectiveness of joint missions.

Finally, the F-45 combines the best features of its predecessors and introduces several enhancements. It leverages artificial intelligence for mission planning and execution, streamlining complex operations. The aircraft is also equipped with the latest in propulsion technology, resulting in improved fuel efficiency and performance at high altitudes.

Each of these aircraft models is designed with specific missions in mind, showcasing a commitment to innovation and technological advancement in aviation. With features that enhance their performance, adaptability, and combat readiness, the Delta 40, F-25, F-30, F-35, and F-45 represent the future of aviation technology. Their development signifies an important step toward maintaining technological superiority in both military and commercial aviation sectors.
Top Page Image Contents