Delta F-25, 35, 30 Section I Pre-Installation Items, Code Compliance, Determining Product Location

Page 10

Pre-Installation Items

SECTION I - Pre-Installation Items

Code Compliance

This product must be installed in accor- dance to the following:

All applicable local, state, national and provincial codes, ordinances, regula- tions and laws.

The National Fuel Gas Code NFPA54/ ANSI Z332.1 - Latest edition.

Installation of Oil Burning Equipment NFPA 31 - Latest Edition

National Electric Code ANSI/NFPA 70.

For installations in Canada -“Installation Code for Gas Burning Equipment” CGA/B149.

For installations in Canada - Installation code for Oil Burning Equipment - CSA/B139.

Determining Product Location

Before locating the ELITE check for conve- nient locations to:

-Domestic water supply piping

-Heating system piping

-Venting

-Gas or oil supply piping

-Electrical service

Ensure the area chosen for the installation of the ELITE is free of any combustible materials, gasoline and other flammable liquids.

WARNING

Failure to remove or maintain the area free of combustible materials, gasoline and other flammable liquids or vapors can result in severe personal injury, death or substantial property damage.

Ensure the ELITE and its controls are protect- ed from dripping or spraying water during nor- mal operation or service.

The ELITE should be installed in a location so that any water leaking from the tank or piping connections or relief valves will not cause damage to the area surrounding the unit or any lower floors in the structure.

-When such a location is unavoidable a suitable drain pan with adequate drainage should be placed under the unit. The drain pan must not restrict the flow of combustion air to the unit.

Boiler Replacement

If the ELITE is replacing an existing boiler / hot water heater system, the following items should be checked and corrected prior to instal- lation:

Primary and domestic piping leaks and corrosion.

Improper location and sizing of the expansion tank on the primary heating loop.

Improper sizing of the thermal expan- sion tank (if used) on the domestic sup- ply line.

Vent condition and sizing.

Recommended Clearances

The ELITE is approved for zero clearance to combustibles, excluding the vent hood and vent piping.

Vent hood and vent piping - 6 inches from combustible materials when using type “L” double wall vent.

Vent Piping - 18 inches from combustible materials when using single wall vent.

Primary and domestic hot water piping - 1 inch from combustible material.

5

Image 10
Contents Installation a N D M a I N T E N a N C E For Your SafetyTable of Contents Section V Primary Piping Section Viii Internal Wiring Section Xiii CHECK-OUT Procedures Product & Safety Information HOT Ber and the serial number from the rat Ing label when inquiring about service orTroubleshooting Triangle Tube accepts no liability for anyOperating Restrictions Code Compliance Section I Pre-Installation ItemsBoiler Replacement Determining Product LocationResidential Garage Installations Section II Providing Air for Combustion and Ventilation Removal of an Existing Boiler from a Common Vent System Handling Instructions Hydrostatic Test ProceduresSection III Unit Preparation Hydrostatic Pressure TestCompletion of Hydrostatic Test and Draining General Piping Requirements Temperature / Pressure Relief ValveSection IV Domestic Piping Domestic Supply PressureDomestic Piping Multiple Units Installation Storage Tank ApplicationDomestic Piping Diagrams TR/SMART Series ApplicationElite With Recirculation Domestic Piping Elite with Storage TankSection V Primary Piping Sizing Primary Piping Closet Zero Clearance ApplicationsSystem Piping Zone Circulators Primary Piping Near Appliance Piping Install balancing valves to Primary Piping Low Temperature Radiant System Primary Piping Multi Units Installation Section VI Venting Repair any damaged chimney mor- tar or jointsOil Vent Direct Vent Applications Masonry and Metal Chimneys Gas Venting -General RequirementsType B Vent Systems Vent Connectors Section VII Fuel Piping Recommended Gas Supply PipingPipe Sizing Propane Gas Pipe Sizing Natural GasNatural Gas Supply Pressure Requirements Propane Gas Supply Pressure RequirementsGeneral Oil Piping Guidelines Section Viii Internal Wiring Elite Factory Internal WiringWire Color Code Outdoor Temperature Limit Section IX External WiringInstallation Compliance Line Voltage ConnectionsMultiple Zone Field Wiring Using Zone Valves Field wiring with zone circulators Typical Zone Relay Panel Wiring Section X Start Up Preparation Filling the Outer Primary Tank and System Check Low Water Cut-Off Device Final Checks Before Start-up Section XI Start-Up ProceduresElite Start-up Recommended Combustion Levels Section XII Temperature Limits Recommended Primary Thermostat SettingTemperature Limits Section XIII- Check-Out Procedures Section XIV Installation Record Section Xvii Replacement Parts Jacket Components Control Panel Components Electrical Panel Components Specifications Elite Data TTP Brazed Plate Heat Exchangers Maxi-flo Pool and Spa Heat Exchangers

45, 30, 35, 40, F-25 specifications

Delta 40, F-25, F-30, F-35, and F-45 represent a new generation of aircraft designed to meet the evolving demands of modern aviation. These aircraft are equipped with advanced technologies, making them suitable for various missions, including cargo transport, surveillance, and multirole combat operations. Each model in this series comes with its own set of features and capabilities.

The Delta 40 stands as a versatile platform known for its impressive range and payload capacity. Its advanced avionics system ensures enhanced situational awareness and operational efficiency. The aircraft employs composite materials for improved fuel efficiency and reduced maintenance costs. Furthermore, Delta 40 is equipped with state-of-the-art navigation systems that include GPS, inertial navigation, and terrain awareness features.

The F-25 is designed with a focus on agility and speed. It features advanced thrust vectoring technology that allows for greater maneuverability, making it effective in air-to-air combat situations. The aircraft leverages stealth technology, incorporating radar-absorbing materials that reduce its visibility to enemy radar systems. This model also includes advanced electronic warfare capabilities for defensive operations.

Moving on to the F-30, this aircraft serves as a heavy-lift solution, optimized for cargo transport. Its spacious cargo bay can accommodate a wide range of freight, and its loading ramp facilitates quick turnaround times for ground operations. The F-30 utilizes a fly-by-wire control system to enhance stability and control during flight. Additionally, this model is equipped with advanced communication systems that allow for seamless integration into joint operations.

The F-35 integrates cutting-edge technologies to provide multirole capabilities. It boasts an advanced sensor suite that enables real-time data sharing among allied forces. The aircraft's stealth capabilities and advanced electronic warfare systems make it a formidable presence on the battlefield. Its interoperability with various platforms enhances the overall effectiveness of joint missions.

Finally, the F-45 combines the best features of its predecessors and introduces several enhancements. It leverages artificial intelligence for mission planning and execution, streamlining complex operations. The aircraft is also equipped with the latest in propulsion technology, resulting in improved fuel efficiency and performance at high altitudes.

Each of these aircraft models is designed with specific missions in mind, showcasing a commitment to innovation and technological advancement in aviation. With features that enhance their performance, adaptability, and combat readiness, the Delta 40, F-25, F-30, F-35, and F-45 represent the future of aviation technology. Their development signifies an important step toward maintaining technological superiority in both military and commercial aviation sectors.